haha, that was a old post, I know you always update it to last version upon release of new SC/EOSSwitchcraft 1.3.0. The Venom always include bleeding edge software.
haha, that was a old post, I know you always update it to last version upon release of new SC/EOSSwitchcraft 1.3.0. The Venom always include bleeding edge software.
Echando a perder se aprende.Switchcraft 1.3.0. The Venom always include bleeding edge software.
If you are not aware of what you are doing, then just use the default settings, they are optimal for 99% of consoles.If the console does not boot when the UV level is raised, use the boot mode without a kip via Hekate INI folder and roll back this setting. Happy overclocking.
Source code is closed because of idiocracy of some people not respecting the open source.has there ever been a source release for the newest oc stuff yet? or all still discord?
https://discord.gg/JNfjDfSUAnyone have the discord link/invite please? I'm on CFW Stock and miss ram overclock
On github in the issues section there are people who say that there is no support for 18.10 on the OLERD switch.Yes it does.
You have to join the discord I posted above and go to overclocking section and ask in there, the OC suite on github is old and outdated, the new stuff is on discord...On github in the issues section there are people who say that there is no support for 18.10 on the OLERD switch.
I joined the group, it says I don't have permission to postYou have to join the discord I posted above and go to overclocking section and ask in there, the OC suite on github is old and outdated, the new stuff is on discord...
check the Rules and get a Role.I joined the group, it says I don't have permission to post
Hey! I'm using an old version of EOS that no longer works properly on HOS 18.1. I'm afraid to use switchvenon/switchcraft. Could I please get an invitation to access the Discord channel with the latest version of EOS and instructions? Thankshaha, that was a old post, I know you always update it to last version upon release of new SC/EOS
https://discord.gg/AYjRBTppHey! I'm using an old version of EOS that no longer works properly on HOS 18.1. I'm afraid to use switchvenon/switchcraft. Could I please get an invitation to access the Discord channel with the latest version of EOS and instructions? Thanks
1862mhz any Erista can do it, the corruption can happen at any frequency cause it depends more of the voltage used and ram timings Vs frequency. Erista starts getting hard is usually above 1996mhz and too much MHz with low voltage might corrupt but not very usual, the worse is bad timings...the original thread mentions a risk of sd or nand corruption for v1 switches using 18xx ram speed.
is that like, a constant threat that can happen at any time or would you know essentially instantly if your system cant handle that setting?
I use the emulator without overclocking, do I still run the risk of breaking anything?1862mhz any Erista can do it, the corruption can happen at any frequency cause it depends more of the voltage used and ram timings Vs frequency. Erista starts getting hard is usually above 1996mhz and too much MHz with low voltage might corrupt but not very usual, the worse is bad timings...
Mine is currently at 2169mhz with tight timings but I have memory coolers and have a lot of over voltage 1.3125v which I don't recommend but my mum's suck, some lucky ppl can do 2131mhz with even less than 1.175v, mine needs 1.25+v.
Ps: just have a backup of Ur latest emunand and do it only in emunand, if it corrupts 0 problems, just copy paste the backup of the good emunand back to the mSD...
https://discord.gg/GuE4tdG7XtI am on 18.0.1 and had used the github files without realizing they are outdated. Can I please get an invite for the discord channel to get the latest file? I want to be able to overclock ram to 1800.