Hacking Hardware Picofly - a HWFLY switch modchip

[QuiTim]

Hello, gentlemen, do these two resistors have the same values?

4.7Kohm 0201 both of them

 

[jmmc]

The flex v2. V3. Lite Flex. Is same value to sp1 sp2. On nintendo switch lite.???

Yes, you can use V2/3 on v2 switch, lite and oled.

 

[Danook28]

Yes, you can use V2/3 on v2 switch, lite and oled.

Thank you brother

 

[jmmc]

I used 6 2040-tiny today. Three of the switches (V1/V2) of Samsung emmc have emmc slow error.

With just the integrated 47ohm resistors or have you added one more to dat0 and cmd?

 

[Cristiano04]

4.7Kohm 0201 ambos

obrigado mano

 

[Kiuxn]

With just the integrated 47ohm resistors or have you added one more to dat0 and cmd?

The revised tiny integrates 45 ohm resistors.

 

[Adran_Marit]

I use and adaptor that came with the micro SD.

The brand it's Kingston Canvas Select Plus.

I'm 99% sure that's not Micro SD fault, because I can get into UMS mode and see the SD card on the PC with USB C on the switch.

I can play with the GPP partitions and the Boot0 and Boot1 too.

I try with exFat and FAT32 too.

Hmm try a different sd card and windows or Mac?

 

[cgtchy0412]

No issue with that Kingston Canvas select plus, been using it few times.

 

[jmmc]

The revised tiny integrates 45 ohm resistors.

I thought they were 47 thx. But did you add a “second” resistor to fix slow emmc error?

 

[mian_85_]

Hi guys,

Installing the picofly I burned the CMD resistor in my OLED switch.
I read in other post that the resistor that is sitting on the CMD point is 4k7 ohm and the one beside that is 47k ohm, both 0201 size.
Can you confirm the value and the size?

I want to confirm before order them.

Thanks and regards

 

[Arakon]

I thought they were 47 thx. But did you add a “second” resistor to fix slow emmc error?

These resistors usually have a 10% margin of error plus some resistance over the wire itself that changes with length, so 45 and 47 are close enough to make no difference.

 

[Danook28]

Im finish install pico fly on my console lite. The pico boot slow. Is there any fix. Im use 3.73 firmware.

 

[Switxh]

Im finish install pico fly on my console lite. The pico boot slow. Is there any fix. Im use 3.73 firmware.

I have an OLED that has slow glitch times on the Pico too. Are you using mosfets or a HWFLY CPU flex?

 

[Takezo-San]

Im finish install pico fly on my console lite. The pico boot slow. Is there any fix. Im use 3.73 firmware.

Picture of install please

 

[Danook28]

I have an OLED that has slow glitch times on the Pico too. Are you using mosfets or a HWFLY CPU flex?

Flex v3

 

[cowboy619]

Im finish install pico fly on my console lite. The pico boot slow. Is there any fix. Im use 3.73 firmware.

Check resistors and solder points


Sent from my iPhone using Tapatalk

 

[Switxh]

Check resistors and solder points


Sent from my iPhone using Tapatalk

I have slow glitching Pico too. The resistors are not shorted and the diode readings for those points are in range but the CPU point 15 on the Pico measures 1.119 v which I think is too high as I've heard it should be around 0.500. Do you have any idea what could cause the high reading on CPU point on the Picofly?

 

[Danook28]

Picture of install please

Im sorry it is first install. And any thing wrong plz told me what I do wrong. Thanks. Im still not soldring Flex legs i was thinking on my console it is new.

 

[cowboy619]

Im sorry it is frist install. And any thing wrong plz told me what I do wrong. Thanks. Im still not soldring Flex legs i was thinking on my console it is new.

Those resistors are holding on for dear life. Check diode readings on all points and report back with values


Sent from my iPhone using Tapatalk

 

[DejavuStudio]

My work for oled with 2.73
Instant boot in 1s, so surprise.
Thanks allll