Hacking Hardware Picofly - a HWFLY switch modchip

[Lightboubou]

resistors already soldered *bottom right*

That's what I though but I wanted to be sure. Thanks

 

[jacopo99]

PICOFLY ИX module (verified)

Use easyeda PRO

The CPU cable will be released later
The resistor uses 0402 and is not recommended for novice welding
The circuit board is 0.8mm thick

V0.8.1+ supports jumpers, V1 V2 LITE OLED universal

Have you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.

BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.

 

[Alpuerto213]

Change the resistance,D0 USE 100Ω,ohter use 47Ω

What are the proper reading in each point?

 

[darviral]

NS OLED Pico Installation Done! some Switch need 2 mosfet

 

[Modi]

NS OLED Pico Installation Done! some Switch need 2 mosfet

Dont Look Clean but works

 

[Marsowaty]

Hey, i have a three problems on my switch lite

First see a video: Pico fly led blue and green? And Start only OFW

Second problems switch not reading micro sd:

Three problems: I put together an aluminum heatsink and fault. Switch off and not reaction.

 

[darviral]

Dont Look Clean but works

Yes it's difficult to clean install this one

 

[abal1000x]

.

 

[SQc04]

Have you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.

BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.

You can modify it yourself

Post automatically merged: May 4, 2023

What are the proper reading in each point?

It needs to be tried, and the situation is different for different EMMCs

Post automatically merged: May 4, 2023

Have you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.

BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.

Empty wires in the filled area need to be retained, otherwise they will not be connected after filling
The filling area is copper-paved

Post automatically merged: May 4, 2023

Have you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.

BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.

like this

 

[NetYaroze]

No one help me?

 

[abal1000x]

.

 

[QuiTim]

No one help me?

Check messages, I sent you a list

 

[Flaviocarvalho]

Can anyone tell me what component is this and if its necessary for switch turn on? Its near emmc on swotch lite

 

[Modi]

Can anyone tell me what component is this and if its necessary for switch turn on? Its near emmc on swotch lite

Hey it resistor 100ohm size 0201

 

[789-Benny]

Know what would be nice if someone uploaded free schematics for the rp2040 flex cable (just like the board on github), so that we can use use places like jlcpcb or whoever else and order them cheaper and quicker

@SQCseems to have uploaded .zip to his repo for the flex cable, the emmc folder is for what?

 

[Marsowaty]

Blue Green but OFW, i experience this. The problem is there is a mold of tin that lying around in the pico board (i am in a hurry when install it, two week ago is a big holiday for me, so i need to mod it ASAP). The junk tin short-circuit-ed some part of the pico board (Its around the D0, CMD, CLK). Take out the junk tin and its work again.

Try to check using Continuity test to check maybe theres some SC occured.

Picofly working one week ago Working maybe two hour and error message popped up Micro-sd. I turned off the switch. And now a have a problem error
I check bridged point on rp2040, but i didn't find it.

 

[calishooter]

I'm currently on v2.65. Can someone please explain to me the difference in v2.66 and v2.67.
I read something about fuse burning. Thanks!

 

[SkylerTakashi]

How can i use a V1 flex cable on a V2 Mariko Nintendo switch?

 

[Modi]

How can i use a V1 flex cable on a V2 Mariko Nintendo switch?

Yes you can

 

[SQc04]

Know what would be nice if someone uploaded free schematics for the rp2040 flex cable (just like the board on github), so that we can use use places like jlcpcb or whoever else and order them cheaper and quicker

@SQCseems to have uploaded .zip to his repo for the flex cable, the emmc folder is for what?

The EMMC cable is still being verified