That's what I though but I wanted to be sure. Thanksresistors already soldered *bottom right*
That's what I though but I wanted to be sure. Thanksresistors already soldered *bottom right*
Have you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.PICOFLY ИX module (verified)
Use easyeda PRO
The CPU cable will be released later
The resistor uses 0402 and is not recommended for novice welding
The circuit board is 0.8mm thick
V0.8.1+ supports jumpers, V1 V2 LITE OLED universal
What are the proper reading in each point?Change the resistance,D0 USE 100Ω,ohter use 47Ω
Dont Look Clean but worksNS OLED Pico Installation Done! some Switch need 2 mosfet
Its okay to use solder wick.for example
i want to resolder the point, i need clean old lead.
is it safe to use solder wick
im afraid it will broke the pad point
Blue Green but OFW, i experience this. The problem is there is a mold of tin that lying around in the pico board (i am in a hurry when install it, two week ago is a big holiday for me, so i need to mod it ASAP). The junk tin short-circuit-ed some part of the pico board (Its around the D0, CMD, CLK). Take out the junk tin and its work again.Hey, i have a three problems on my switch lite
First see a video: Pico fly led blue and green? And Start only OFW
View attachment 368848
Second problems switch not reading micro sd:
View attachment 368844
Three problems: I put together an aluminum heatsink and fault. Switch off and not reaction.
View attachment 368846
You can modify it yourselfHave you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.
BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.
It needs to be tried, and the situation is different for different EMMCsWhat are the proper reading in each point?
Empty wires in the filled area need to be retained, otherwise they will not be connected after fillingHave you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.
BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.
like thisHave you considered adding the 1010 ws2812b C5349953 ? I gave it a check and fits no problem. It's also compatible with PCBA from jlc. Fully assembled it should come at about 90 dollars for 5 boards.
BTW I get multiple stray tracks where the fill region should be and slightly unconnected ones elsewhere.
Microscope is a must. I prefer HDMI microscope, but cheap microscope also work.Good morning everyone! Can er tell me a good soldering iron, the solder wire, the correct wires for soldering on the right points and the flux, suitable for installing picofly? I have a person who would do the picofly install but doesn't have everything needed (except the technique). I tried to install myself picofly but with bad results because I used tools that didn't help me and I would like to provide everything I need.
Thanks!
Check messages, I sent you a listNo one help me?
Hey it resistor 100ohm size 0201Can anyone tell me what component is this and if its necessary for switch turn on? Its near emmc on swotch lite
Picofly working one week ago Working maybe two hour and error message popped up Micro-sd. I turned off the switch. And now a have a problem errorBlue Green but OFW, i experience this. The problem is there is a mold of tin that lying around in the pico board (i am in a hurry when install it, two week ago is a big holiday for me, so i need to mod it ASAP). The junk tin short-circuit-ed some part of the pico board (Its around the D0, CMD, CLK). Take out the junk tin and its work again.
Try to check using Continuity test to check maybe theres some SC occured.
Yes you canHow can i use a V1 flex cable on a V2 Mariko Nintendo switch?
The EMMC cable is still being verifiedKnow what would be nice if someone uploaded free schematics for the rp2040 flex cable (just like the board on github), so that we can use use places like jlcpcb or whoever else and order them cheaper and quicker
@SQCseems to have uploaded .zip to his repo for the flex cable, the emmc folder is for what?