Hacking Hardware Picofly - a HWFLY switch modchip

[OMAR1982]

OLED Modding with Picofly RP-2040 Zero can anyone summarize the soldering points

 

[Danook28]

OLED Modding with Picofly RP-2040 Zero can anyone summarize the soldering points

Dat 0 adapter and flex cable v2 cpu. 47R smd resistor. Rp2040 chip. And digram hwfly chip oled on youtube bro.

 

[juanvlc]

just built the adapter since i didnt have the otherside of the connector so i pealed of a bit and solderd it to it and addes some uv resin for streng and well guess what im able to flash it

edit: i realized the picture is uploaded showed outter bridges so i added it so no one bridges THEM xD



View attachment 360557View attachment 360579

View attachment 360558

Many thanks mate!!! You are very talentous and clever

 

[brecht6]

View attachment OLED-DIAGRAM.jpg
This oled diagram should be correct I think. Can anyone confirm?

 

[linuxares]

So the price drops begin

View attachment 361208

Oh I heard via my sources this is the only chip that the Toshiba memories works great on. Even HWFly got some issues with them.

 

[juanvlc]

View attachment 361275
This oled diagram should be correct I think. Can anyone confirm?

Yes mate, you are correct

 

[snaker]

just built the adapter since i didnt have the otherside of the connector so i pealed of a bit and solderd it to it and addes some uv resin for streng and well guess what im able to flash it

edit: i realized the picture is uploaded showed outter bridges so i added it so no one bridges THEM xD



View attachment 360557View attachment 360579

View attachment 360558

Hello,can you please tell me what type of clear glue do you use ? Thanks.

 

[froggestspirit]

Is there any way to change the pins used? I have a couple Tiny2040, they have all the pins needed minus pin 15

 

[detilmalala]

Yes u will have to install a second MOSFET like @rehius said I had the same issue after installing second MOSFET it worked fine

would you share a diagram for 2 mosfet intallation?

 

[juanvlc]

Hello,can you please tell me what type of clear glue do you use ? Thanks.

https://a.aliexpress.com/_EJtElpD
That one I suppose

 

[billybobxxx]

Is there any way to change the pins used? I have a couple Tiny2040, they have all the pins needed minus pin 15

you need this pin...dont seem to have SPI1 TX anywhere on this tiny2040 but you can give a shot to pin 3 or 7 on you tiny2040 maybe it will work because its also I2C1 SCL its my guess....

 

[snaker]

https://a.aliexpress.com/_EJtElpD
That one I suppose

Thank you very much!

 

[llskankzll]

I'm using RP2040 one and I'm only getting one quick red light. Is it my installation or the chip is blank (i hold down boot, plug it in and drop the 2.5 fw.ufc & reboot)? I'm using the v2 hwfly cpu cable on a v2 (use the 3, 4 or 3-4 points on the cable), added 47 ohm on the 3 points and 20 ohm on the reset point. I tried my wiring (removed the wire on the cpu cable and removed the resistors) with hwfly oled chip and it boot up.

 

[billybobxxx]

I'm using RP2040 one and I'm only getting one quick red light. Is it my installation or the chip is blank (i hold down boot, plug it in and drop the 2.5 fw.ufc & reboot)? I'm using the v2 hwfly cpu cable on a v2 (use the 3, 4 or 3-4 points on the cable), added 47 ohm on the 3 points and 20 ohm on the reset point. I tried my wiring (removed the wire on the cpu cable and removed the resistors) with hwfly oled chip and it boot up.

Try to remove the 20 ohm resistor on the reset..try without anything. If its not working you can try with 20k ohm or 30k ohm on rst point.

 

[lufeig]

CYAN - no reaction to glitch. try installing second mosfet like on the picture few pages ago

Yes u will have to install a second MOSFET like @rehius said I had the same issue after installing second MOSFET it worked fine

thanks @rehius and @Dee87!

I installed a second mosfet as per instruction, but it keep booting to OFW and a red screen.

I'll order a lite ribbon cable and try again when it arrives. It seems I can't install mosfets adequately.

 

[Dee87]

Many thanks mate!!! You are very talentous and clever

very nice my friend whats the button size u used ?

Post automatically merged: Mar 25, 2023

would you share a diagram for 2 mosfet intallation?

Klick me thats for mariko board

 

[juanvlc]

very nice my friend whats the button size u used ?

very nice my friend whats the button size u used ?

Post automatically merged: Mar 25, 2023

Klick me thats for mariko board

https://amzn.eu/d/grW4bSK

 

[Dee87]

https://amzn.eu/d/grW4bSK

okay il see if i find some also

 

[froggestspirit]

you need this pin...dont seem to have SPI1 TX anywhere on this tiny2040 but you can give a shot to pin 3 or 7 on you tiny2040 maybe it will work because its also I2C1 SCL its my guess....

Nah, im pretty sure it has to be enabled on a software level. Them being I2C1 just means they can't both be configured to it at the same time with different signals. Might not be too hard to modify on an asm level..

 

[Dee87]

Hello,can you please tell me what type of clear glue do you use ? Thanks.

UV Resin is what i used in that picture