MicroSD won't fit into my CycloDS

Discussion in 'CycloDS' started by Atmosphere, Jan 10, 2009.

Jan 10, 2009
  1. Atmosphere
    OP

    Newcomer Atmosphere Member

    Joined:
    Feb 5, 2007
    Messages:
    11
    Country:
    United States
    Today i received my CycloDS from Dealwoot.com when i opened it up and tried to insert my SD card would not even go in all the way in. As if the SD slot is shallow. is this a known issue with CycloDS or dealwoot?. getting the SD card out after putting it into the Cyclo is a pain its stuck in there tight and i have to pull it out hard to get my microSD back. and Yes i am putting it in the right way.
     
  2. DeMoN

    Member DeMoN GBAtemp Guru

    Joined:
    May 12, 2004
    Messages:
    7,647
    Country:
    United States
    Does it work though? Many flash cards have the problem where the MicroSD sticks out even after being pushed fully in. This could be caused by either a defect in the microSD or the flash card. Unfortunately you'll just have to ignore it, or grind off a few millimeters off the top of the microSD.
     
  3. Atmosphere
    OP

    Newcomer Atmosphere Member

    Joined:
    Feb 5, 2007
    Messages:
    11
    Country:
    United States
    I can get it to fit in Flush but that requires me pushing down on it harder then i like. But getting it out i almost have to get my teeth to get a grip good enough to yank it out. Does the slot need to be broken in or should i go for an RMA. its stuck in there really tight when its in there fully.
     
  4. wilddenim

    Member wilddenim Candy!

    Joined:
    Sep 4, 2007
    Messages:
    972
    Location:
    UK
    Country:
    United Kingdom
    Yeah, that's normal with brand new micro cards and flashcarts. After a few times, it'll go in smoothly. I've got my CycloDS for 11 months now, I can remember when I had to yank it out. Now it goes in easily.
     
  5. Isaiah

    Member Isaiah The Conductor

    Joined:
    Aug 24, 2008
    Messages:
    525
    Location:
    Brisbane
    Country:
    Australia
    Yeah this is normal with cyclo's just keep on pulling out in putting in. it'll eventually loosen up.
     
  6. Priss

    Member Priss GBAtemp Regular

    Joined:
    Oct 18, 2008
    Messages:
    209
    Location:
    Hamilton, Ontario
    Country:
    Canada
    I think I had a different mind set when reading this thread....

    You still haven't mentioned if it works or not [​IMG]
     
  7. tinymonkeyt

    Member tinymonkeyt GBAtemp brat

    Joined:
    Feb 27, 2008
    Messages:
    3,221
    Country:
    United States
    well some cyclos are prob the older batch and the micro sd is supposed to stick out for easier way to get it out.
    mine sticks out about 1mm or so but it still works
     
  8. kevenka

    Member kevenka GBAtemp Advanced Fan

    Joined:
    Jul 15, 2007
    Messages:
    930
    Location:
    Texas
    Country:
    United States
    it's a known issue that the micro sd sticks out about 1 mm...and as for the fact that it's tight, it'll loosen up overtime.
     
  9. Atmosphere
    OP

    Newcomer Atmosphere Member

    Joined:
    Feb 5, 2007
    Messages:
    11
    Country:
    United States
    LOL i see what you mean looking back [​IMG]

    The Cyclo works fine after awhile think it must of loosen it up a bit. Before it was extremely hard to get the MicroSD back out of the Cyclo once it was in there all the way now its still a bit of a pain but not as much. Though I'm sure over time it will get easier. Thanks everyone for there comments.
     

Share This Page