Last edited by Sushi4life,
you can put it where the point where even if the two of them are missing , make sure you touch the track/line to those point.View attachment 202343Is there an alternate point for the microSD? I somehow managed to rip that tiny dot
you can put it where the point where even if the two of them are missing , make sure you touch the track/line to those point.
if you can't , there is another solution don't worry , but it's necessary to remove the motherboard .
you have to solder on the flip motherboard side , there are the same point.
edit : take a look here , 2nd page #30 post
https://gbatemp.net/threads/about-the-microsd-card-connector.523130/page-2
@Xyphoseos your mSd card reader seams ok , there are no apparent disoldered pins.
-for the materials , you need some AWG40 wire , like @LittlestCube tube does/buy , he could advice you
-for the missing pin in you are right it's orange ; and to make sure :
sorry ,i never ordered those wires and my materials are generic ones , found on traditional stores.Could you give me links please ? a good site ^^'
Mmmh... Of course, it is better to waitsorry ,i never ordered those wires and my materials are generic ones , found on traditional stores.
my soldering iron has +10 years old , and i used a fat wire ( not recomended ) like you saw in 1st page.
since all stores are closed , you still can find those in the super market of your town ( where electronics are)
but be carefull and wear a mask.
personally i don't order on internet store for now ( amazon ....)
because someone can contract this COVID-19 by my fault ( warehoused dispatchers/ deliverers / postal employees )
since it's just my personal opinion , every one do what he could right now
it's a normal one , cost me 5 euro ( 7 dollars )Mmmh... Of course, it is better to wait
Just to know, you soldering iron is make for little sordering or it is normal ?
@Sushi4life
edit : i take a look at the image and here you go
in the circle you can eventually solder there.
the problem is the arrows , it seams there is no line/track countinuing to that point , i hope im wrong.
but if it's true , you have to solder in the flip side of the motherboard.
Yes sadly the line was broken. I did solder to the point but when I pulled a bit the wire to adjust the placement of it, the line started to rip away from the board . I am trying to find some hint on where to solder at the back. The only guidance was from this thread where someone had a similar problem but different missing pin : https://gbatemp.net/threads/about-the-microsd-card-connector.523130/page-2
you can put it where the point where even if the two of them are missing , make sure you touch the track/line to those point.
if you can't , there is another solution don't worry , but it's necessary to remove the motherboard .
you have to solder on the flip motherboard side , there are the same point.
edit : take a look here , 2nd page #30 post
https://gbatemp.net/threads/about-the-microsd-card-connector.523130/page-2
@Xyphoseos your mSd card reader seams ok , there are no apparent disoldered pins.
-for the materials , you need some AWG40 wire , like @LittlestCube tube does/buy , he could advice you
-for the missing pin in you are right it's orange ; and to make sure :
the persons who have this issue , have 2,3,4 pins disoldered , so they just solder what missing.Does anyone has a picture with all the test points soldered?
I need to solder all the pins my switch doesn't have the connector. If somebody did that would like to see it... Do I need to also solder the green on the capacitor?the persons who have this issue , have 2,3,4 pins disoldered , so they just solder what missing.
perhaps @LittlestCube ,he has posted an image of the sd reader completely soldered , i think he would solder all points.
- why do you need to see those points soldered ?
i thought you have only missing 2 pins !I need to solder all the pins my switch doesn't have the connector. If somebody did that would like to see it... Do I need to also solder the green on the capacitor?
I will put this repair stuff at a pause since I also have university and there is the self-isolation going on here that made lots of stores close. I might find a clue where to solder at the back of the motherboard and who would be able to in my local area.
Thank you for your help! Sorry that my skills was not enough to make it a success and feel like wasted... At least my switch still works since I used CFW with emunand.