Hacking Hardware Picofly - a HWFLY switch modchip

[BigHorse420]

Just arrived
Any firmware for this?
Note the flex and usb same as hwfly v4
@rehius
@vittorio

Did you get firmware with it? If not, you can save it on your pc with picotool. It might be designed to be pin compatible with rehius firmware as there a 3 resistors next to pin 27 to 29

 

[bilalhassan341]

Can I use a cat6 ethernet cable wire to connect mosfet to APU. Because I have only this right now.

 

[vittorio]

Did you get firmware with it? If not, you can save it on your pc with picotool. It might be designed to be pin compatible with rehius firmware as there a 3 resistors next to pin 27 to 29

firmware is normal uf2

 

[BigHorse420]

firmware is normal uf2

What do you mean with normal?

 

[vittorio]

download uf2 and drag and drop on chip

 

[juanvlc]

link for buy

Sorry but disappeared few minutes after I bought it

 

[vittorio]

Sorry but disappeared few minutes after I bought it

aliexpress?

 

[juanvlc]

Yes

 

[vittorio]

Yes

but the other flat did not send it to you?

 

[juanvlc]

Did you get firmware with it? If not, you can save it on your pc with picotool. It might be designed to be pin compatible with rehius firmware as there a 3 resistors next to pin 27 to 29

i must learn this

but the other flat did not send it to you?

no, just received as you cas see

 

[naize]

I accidentally dropped this while removing the usb port. Can I use rp2040 for the switch when I lose this? Thank u

 

[BigHorse420]

i must learn this

no, just received as you cas see

https://github.com/raspberrypi/picotool

Post automatically merged: Apr 18, 2023

download uf2 and drag and drop on chip

I mean to pull the uf2 from the rp2040 to his pc, so he can safely test with it (assuming it is preflashed)

 

[Mansi]

Check my installation rp2040
Perfectly work. Thk Rehius.

My post on <sorry to much pirated content on site>

 

[swordeye2]

Check my installation rp2040
Perfectly work. Thk Rehius.


View attachment 365647View attachment 365648View attachment 365653View attachment 365654
View attachment 365648View attachment 365649View attachment 365650
View attachment 365651

Thanks for sharingg!

 

[Kiuxn]

The virtual system is stuck in the "shutdown" window. Is it a bug in the Raspberry Pi? V2.65

Post automatically merged: Apr 18, 2023

The virtual system is stuck in the "shutdown" window. Is it a bug in the Raspberry Pi? V2.65

I have had this problem with Switch Endurance Edition and lite models, which has never happened before. I have to doubt the Raspberry Pi V2.65

 

[linuxares]

Sorry @Mansi just a little bit to much pirated material on that site so please no linking to it. Never the less great job!

 

[vittorio]

i must learn this

no, just received as you cas see

flat of clk cmd etc

 

[AaronE]

Doing my install and I think I may have damaged the max77812. Would a damaged max77812 cause a blue screen? I think I knocked the corner of the chip off when removing shields around it. Just wanted to check before I go ordering some and replacing it that it might be the cause of my issue.

Soldering looks good under magnification and the resistance measurement to ground of the wires for the APU caps is about 24 Ohms.

 

[juanvlc]

flat of clk cmd etc

no, nothing.Don´t like upper flex at all. I´ve asked seller for firmware....
Im bussy now, will tray on oled later and report

 

[Mansi]

Sorry @Mansi just a little bit to much pirated material on that site so please no linking to it. Never the less great job!

really? sorry, my bad(
im don't know this.