Unfortunately I don't have a tiny - so I can only go by the reference measurements - for reference here's the fly2040-min measurements next to the tiny's... (mine's smaller )
Also - I've just installed one (fly2040-min) and I can happily confirm it works perfectly.
The nice thing is that it also already has the 3 x 47 Ohm resistors, the boot button (which is also so small it doesn't have to be removed) and an optional mosfet pulldown resistor (10K). Just solder the jumper to use the pulldown.
Unfortunately I don't have a tiny - so I can only go by the reference measurements - for reference here's the fly2040-min measurements next to the tiny's... (mine's smaller )
Also - I've just installed one (fly2040-min) and I can happily confirm it works perfectly.
The nice thing is that it also already has the 3 x 47 Ohm resistors, the boot button (which is also so small it doesn't have to be removed) and an optional mosfet pulldown resistor (10K). Just solder the jumper to use the pulldown.
I'm going to release (in the same git) a programmer board. But the intention is to use a pogo-pins clip (Search ali for something like: "1.27mm 6P PCB Clip Clamp Fixture Probe Tool Programming Download Burning PCB Debugging Inspection Tool")
For testing I just cut a USB cable and put a 3V3 regulator on a prototyping board, ran D+ & D- through, GND & 3V3 to my clip.
I'm going to release (in the same git) a programmer board. But the intention is to use a pogo-pins clip (Search ali for something like: "1.27mm 6P PCB Clip Clamp Fixture Probe Tool Programming Download Burning PCB Debugging Inspection Tool")
For testing I just cut a USB cable and put a 3V3 regulator on a prototyping board, ran D+ & D- through, GND & 3V3 to my clip.
Programmer board coming.
It's open source - https://github.com/floxcap/fly2040/tree/main/pcb/fly2040_min
But if there's enough interest I'll look at doing a bulk order at JLCPCB which will make pricing quite reasonable - and then I'd be happy to sell.
The pull down is connected to the solder jumper (normally disabled by default) and the other side of the jumper is connected to the CPU pad.
I'm going to release (in the same git) a programmer board. But the intention is to use a pogo-pins clip (Search ali for something like: "1.27mm 6P PCB Clip Clamp Fixture Probe Tool Programming Download Burning PCB Debugging Inspection Tool")
For testing I just cut a USB cable and put a 3V3 regulator on a prototyping board, ran D+ & D- through, GND & 3V3 to my clip.
Post automatically merged:
If you're doing quite a few of these - you only need 1 programmer set-up.
Of course also - once installed - the normal upgrade bin would be used.
Post automatically merged:
Programmer board coming.
It's open source - https://github.com/floxcap/fly2040/tree/main/pcb/fly2040_min
But if there's enough interest I'll look at doing a bulk order at JLCPCB which will make pricing quite reasonable - and then I'd be happy to sell.
The pull down is connected to the solder jumper (normally disabled by default) and the other side of the jumper is connected to the CPU pad. View attachment 377303
Not really... There's a potential for the mosfet(s) to carry a charge when the fly is in a sleep state or powering up. The (weak) pull-down is an option to ensure the mosfet(s) gate isn't floating at those times. The alternative is to have it at the mosfet side.
-Will you be selling these?
-If yes, how much will a board and flex cable order from you approximately cost?
-Does the latest fly2040_min board work on the Lite?
-Will you be selling these?
-If yes, how much will a board and flex cable order from you approximately cost?
-Does the latest fly2040_min board work on the Lite?
If there's enough interest - then I'd consider it.
Tested on the lite and on V2 and working perfectly.
Currently testing if it works with the mosfet(s) on the same board which will simplify the install and reduce the cost.
I'd be looking at selling for around $6 USD (but would probably set a minimum order amount because shipping is a hassle and I'm not doing it for profit).
If there's enough interest - then I'd consider it.
Tested on the lite and on V2 and working perfectly.
Currently testing if it works with the mosfet(s) on the same board which will simplify the install and reduce the cost.
I'd be looking at selling for around $6 USD (but would probably set a minimum order amount because shipping is a hassle and I'm not doing it for profit).
Wonderful! I already found the flex cables in a shop in my country, so I won't have to import those as well. I will go order 5 of the min board then to install. Oh and one more thang, is the v2 the patched unit?(Detective Columbo Stinger)
Rapid Fire Edits: If I get the min boards for the lite, what HW_Fly CPU flex cable should I get as well? And how should I configure my order on JLC's site? Should I even get a flex cable?
Can you provide a photo with the best place to put the board on in the Lite and the solder spots?
Wonderful! I already found the flex cables in a shop in my country, so I won't have to import those as well. I will go order 5 of the min board then to install. Oh and one more thang, is the v2 the patched unit?(Detective Columbo Stinger)
Rapid Fire Edits: If I get the min boards for the lite, what HW_Fly CPU flex cable should I get as well? And how should I configure my order on JLC's site? Should I even get a flex cable?
Can you provide a photo with the best place to put the board on in the Lite and the solder spots?
It's an option if not using the CPU flex (v2 etc) cable... i.e. bare mosfet(s) install. The flex cable already has resistors.
I haven't used that option (jumper) yet as I'm waiting on mosfets to test bare mosfet install.
No I have, I am just asking for confirmation. And I am not aware of any documentation specific to the fly2040
Yes I am aware of the AIO thread and the pfg v6.2. I just want to make sure that I have all my tools at hand
A new Nintendo Switch firmware update is here. System software version 18.0.1 has been released. This update offers the typical stability features as all other...
With Apple having recently updated their guidelines for the App Store, iOS users have been left to speculate on specific wording and whether retro emulators as we...
The time has finally come, and after many, many years (if not decades) of Apple users having to side load emulator apps into their iOS devices through unofficial...
TheFlow has done it again--a new kernel exploit has been released for PlayStation 4 consoles. This latest exploit is called PPPwn, and works on PlayStation 4 systems...
Nintendo might just as well be a law firm more than a videogame company at this point in time, since they have yet again issued their now almost trademarked usual...
While rumors had been floating about rampantly as to the future plans of Nintendo, the President of the company, Shuntaro Furukawa, made a brief statement confirming...
Another video game prototype has been found and preserved, and this time, it's none other than the game that spawned an entire franchise beloved by many, the very...
Anbernic is back with yet another retro handheld device. The upcoming RG28XX is another console sporting the quad-core H700 chip of the company's recent RG35XX 2024...
Two classic titles join the Nintendo Switch Online Expansion Pack game lineup. Available starting April 24th will be the motorcycle racing game Extreme G and another...
Nintendo has officially announced that a successor to the beloved Switch console is on the horizon. As we eagerly anticipate what innovations this new device will...
Nintendo has officially announced that a successor to the beloved Switch console is on the horizon. As we eagerly anticipate what innovations this new device will...
While rumors had been floating about rampantly as to the future plans of Nintendo, the President of the company, Shuntaro Furukawa, made a brief statement confirming...
Nintendo might just as well be a law firm more than a videogame company at this point in time, since they have yet again issued their now almost trademarked usual...
With Apple having recently updated their guidelines for the App Store, iOS users have been left to speculate on specific wording and whether retro emulators as we...
The time has finally come, and after many, many years (if not decades) of Apple users having to side load emulator apps into their iOS devices through unofficial...
A new Nintendo Switch firmware update is here. System software version 18.0.1 has been released. This update offers the typical stability features as all other...
TheFlow has done it again--a new kernel exploit has been released for PlayStation 4 consoles. This latest exploit is called PPPwn, and works on PlayStation 4 systems...
After rumour got out about an upcoming NES Edition release for the famed Nintendo World Championships, Nintendo has officially unveiled the new game, titled "Nintendo...
DOOM is well-known for being ported to basically every device with some kind of input, and that list now includes the old retro game console in Persona 5 Royal...
The number of layoffs and cuts in the videogame industry sadly continue to grow, with the latest huge layoffs coming from Microsoft, due to what MIcrosoft calls a...