Hi everyone!
UPDATE: thanks everyone, the issue was indeed that the path was incorrect (and also I didn't concatenate my files properly).
Everything is now back and working in 1.0.0
Great, and thanks again everyone!!
First of all, a quick thank you to the community for the great tools created, I have spent a lot of time reading before joining.
I have a retail 1.0.0 switch, on which I have installed SX 5.1.0 with ChoiDuJourNX. Everything worked fine except that my SD card was in FAT32. I am pretty confident that I chose the ExFat version upon installation, but because the SD card was only ever recognised by the switch when in FAT32, I tried to downgrade (to 3.0.2-0.0 ExFat) to be sure that I did have ExFat with ChoiDuJourNX (keep in mind that I still have only 1 fuse burnt, and I checked this with hekate multiple times, it is still the case).
However, ever since I did this, when I try to launch the firmware with the Launch Firmware option (RaJNX CFW - PreventGCUpdate), it gets stuck at this screen:
Note that I can still boot in RCM mode (in fact, only in this mode because of/thanks to AutoRCM and ChoiDuJourNX), and that payload injection (tested with hekate and RajNX) still works.
I have a full eMMC backup of BOOT0/1 and RAW GPP of my switch before I did any of these modifications (so software version 1.0.0), but when I try to restore it, I have the above Error (4).
Does this mean that my backup is corrupted? What can I do?
UPDATE: thanks everyone, the issue was indeed that the path was incorrect (and also I didn't concatenate my files properly).
Everything is now back and working in 1.0.0
Great, and thanks again everyone!!
TL;DR
00: rawnand.bin (0000000-3A3DFFF)
Filename: Backup/e544439d/Restore/rawnand.bin
Error (4) While opening backup. Continuing...
Time taken: 0m 0s
---
Fuses burnt: 1
Model type: retail
AutoRCM mode activated by ChoiDuJourNX
Software version: 5.1.0-3.0 -> 3.0.2-0.0 (ExFat)
CFW version: RajNX edition v0.7.5.1
Full eMMC backup: 1.0.0
00: rawnand.bin (0000000-3A3DFFF)
Filename: Backup/e544439d/Restore/rawnand.bin
Error (4) While opening backup. Continuing...
Time taken: 0m 0s
---
Fuses burnt: 1
Model type: retail
AutoRCM mode activated by ChoiDuJourNX
Software version: 5.1.0-3.0 -> 3.0.2-0.0 (ExFat)
CFW version: RajNX edition v0.7.5.1
Full eMMC backup: 1.0.0
First of all, a quick thank you to the community for the great tools created, I have spent a lot of time reading before joining.
I have a retail 1.0.0 switch, on which I have installed SX 5.1.0 with ChoiDuJourNX. Everything worked fine except that my SD card was in FAT32. I am pretty confident that I chose the ExFat version upon installation, but because the SD card was only ever recognised by the switch when in FAT32, I tried to downgrade (to 3.0.2-0.0 ExFat) to be sure that I did have ExFat with ChoiDuJourNX (keep in mind that I still have only 1 fuse burnt, and I checked this with hekate multiple times, it is still the case).
However, ever since I did this, when I try to launch the firmware with the Launch Firmware option (RaJNX CFW - PreventGCUpdate), it gets stuck at this screen:
Note that I can still boot in RCM mode (in fact, only in this mode because of/thanks to AutoRCM and ChoiDuJourNX), and that payload injection (tested with hekate and RajNX) still works.
I have a full eMMC backup of BOOT0/1 and RAW GPP of my switch before I did any of these modifications (so software version 1.0.0), but when I try to restore it, I have the above Error (4).
Does this mean that my backup is corrupted? What can I do?
Last edited by Tinkerit,