Thanks!it is also on the emmc Board bottum side
Thanks! exactly what i needed
Thanks!it is also on the emmc Board bottum side
Thanks! exactly what i needed
I got mine from AliE a couple of months ago when this thread started to get serious, that'll be your best bet.has anyone seen seeed XIAO rp2040, is this chip also compatible? - Seems it’s hard to buy RP2040-Zero in UK unless anyone has any best places to buy from?
Agreed! That would of been hilarious
dm meI'm having a hard time getting HOS working on a kiosk unit. Not sure if I'm an idiot with the custom kiosk atmosphere or if it's an issue with the pi firmware.
- Flashed 2.5+unlock
- 47ohm resistors on dat0, cmd, clk
- glitched quickly.
when launching fusee.bin from hekate I get these errors
View attachment 360390
From hekate launch I get this
View attachment 360393
If anyone has a known working sd config that should work on a kiosk unit please zip it up and dm it over if possible. There's a good chance that I'm just goofing up on the software end.
you have not unlocked the firmware, use unlock.uf2 or toolbox hekate payload + unlock.binI'm having a hard time getting HOS working on a kiosk unit. Not sure if I'm an idiot with the custom kiosk atmosphere or if it's an issue with the pi firmware.
- Flashed 2.5+unlock
- 47ohm resistors on dat0, cmd, clk
- glitched quickly.
when launching fusee.bin from hekate I get these errors
View attachment 360390
From hekate launch I get this
View attachment 360393
If anyone has a known working sd config that should work on a kiosk unit please zip it up and dm it over if possible. There's a good chance that I'm just goofing up on the software end.
hot air gun + tweezershow to remove the button and usb port on pico ? any video or images ?
You will need to hook wires up to VB, GND, U+ and U-. Make sure that the 5v only goes to VB on PGA2040, if it ends up elsewhere it will result in a bad time. A USB breakout board is a convenient way of getting at the wires in your USB cableHow could you easily program it?
Yes, the SX Core flex will workcan we use SX Core Flex Cable For SP1 and SP2? Hope Anyone can answer this
This has been answered many times. Yes, you can use flex cables for Erista, Mariko and Oled, but you will still need to solder other points... check the resume post that's been made, all the info is gathered therecan we use SX Core Flex Cable For SP1 and SP2? Hope Anyone can answer this
I dont think reflowing is a good idea.What is the general consensus on DAT0 adapters? Is a friction connection durable enough, or is reflowing a must?
Best would be to reball the eMMC with leaded solder and use a wire for DAT0 between the board via and the eMMC chip or the fancy HWFLY sandwitch green PCB (needs double reball).What is the general consensus on DAT0 adapters? Is a friction connection durable enough, or is reflowing a must?
Search Waveshare RP2040-Zero on AliE, That'll direct you to what you needHi sorry for the noob question is this pi ok for this project or is it a different one and where is the best place to get the flex cable in UK. I've looked on Ali and there seems to be a few different ones
is the toshiba fix on 2.5? can't get any toshiba switch to boot, i've tested on several switches with toshiba, when i swap out to a samsung or hynix, it boots pretty fast consistentlyIt has a really nice statistics algorithm. The more you boot, the better it boots.
It has no training mode, but it saves every successful boot. If you have a good soldering (and not the damn Toshiba eMMC), 10 boots later you get a really well results
Post automatically merged:
Afaik, hwfly guys have already prepared rp2040 boards just in case, so it's a matter of days