Hacking Hardware Picofly - a HWFLY switch modchip

[Weird-Parking356]

The Firmware is not the problem the install has an issue and u need to check what that code says to find the issue thats what its for. put 2.73 back on and let us know what the code says.

Post automatically merged: Jul 19, 2023

and then also send us pictures of ur install

do you have the list of codes meaning¿ the one i am using is for the 3.6, and also what is the confirmation led for the 3.7 fw , i thought it was red like 3.6

Post automatically merged: Jul 19, 2023

do you have the list of codes meaning¿ the one i am using is for the 3.6, and also what is the confirmation led for the 3.7 fw , i thought it was red like 3.6

i mean 2.6 and 2.7 fw

 

[twins333]

do you have the list of codes meaning¿ the one i am using is for the 3.6, and also what is the confirmation led for the 3.7 fw , i thought it was red like 3.6

Post automatically merged: Jul 19, 2023

i mean 2.6 and 2.7 fw

https://github.com/Ansem-SoD/Picofly
You have everything you need there.

 

[Weird-Parking356]

You have everything you need there.

got it

 

[RiotRetroGaming]

Paying him would make him a potential legal target for nintendo, so I think everyone is better off if we stick to saying thanks, think about him instead of our gf/wife, pray to him, name our first born after him, etc

Pfffff FFS

 

[Dee87]

do you have the list of codes meaning¿ the one i am using is for the 3.6, and also what is the confirmation led for the 3.7 fw , i thought it was red like 3.6

Post automatically merged: Jul 19, 2023

i mean 2.6 and 2.7 fw

Read the pined important post or the picofly guide there is everything explained

 

[Weird-Parking356]

Read the pined important post or the picofly guide there is everything explained

i was reading the file and they use 2.74 but the one for download is 2.73 , is the same?

 

[Dee87]

i was reading the file and they use 2.74 but the one for download is 2.73 , is the same?

2.74 is depreciated , yes 2.73 and 2.74 have same debuging

 

[Weird-Parking356]

2.74 is depreciated , yes 2.73 and 2.74 have same debuging

ok , thanks in case i don t get the yellow light i need to the bridge?

 

[Seco_Gobbo2]

yes , thanks i tried the earlier version and it give me the red light confirmation. but now after i install it , the led flash blue and later some kind of between red and purple , any idea?

Hello.

If you are showing a different code than the one on the error code list, I advise you to redo the entire installation.

Use flash_nuke to reset the pico fly, install the 2.73 version directly and redo the welds.

I did the installation on the back of the board, I think it's safer than soldering and heating components on the processor

 

[Weird-Parking356]

Hello.

If you are showing a different code than the one on the error code list, I advise you to redo the entire installation.

Use flash_nuke to reset the pico fly, install the 2.73 version directly and redo the welds.

I did the installation on the back of the board, I think it's safer than soldering and heating components on the processor

thanks a lot for the data , whats the confirmation light it should give after flash? green or yellow?

 

[Dee87]

ok , thanks in case i don t get the yellow light i need to the bridge?

No no need to bridge
Just install it and see what the Morse code gives u don't worrie about the color

 

[Weird-Parking356]

No no need to bridge
Just install it and see what the Morse code gives u don't worrie about the color

ok thanks

 

[Seco_Gobbo2]

thanks a lot for the data , whats the confirmation light it should give after flash? green or yellow?

When you use the nuke flash file the peak does not light up at all.

This file does a factory reset at peak, it stays like when you buy it, ready to receive a new programming file

 

[Weird-Parking356]

When you use the nuke flash file the peak does not light up at all.

This file does a factory reset at peak, it stays like when you buy it, ready to receive a new programming file

i mean when i flash the fw after the nuke

Post automatically merged: Jul 19, 2023

i mean when i flash the fw after the nuke

what color should give with the 2.73 fw

 

[Switxh]

i mean when i flash the fw after the nuke

Post automatically merged: Jul 19, 2023

what color should give with the 2.73 fw

How many times are you gonna ask the same question? The color does not matter with 2.73.

 

[Takezo-San]

i mean when i flash the fw after the nuke

Post automatically merged: Jul 19, 2023

what color should give with the 2.73 fw

You'll get yellow blinks. If you're struggling at this stage I'd do more research to be more ready and confident for the rest of the mod because believe me, the firmware flashing is the easy part. Read and research more till you know the mod process like the back of your hand. You'll be better off in the long run and save yourself a lot more time and stress. The guide does say there are dragon's here....oh its true....its true....

 

[o0SaN0o]

after installing picofly it shows a black screen when an SD card is plugged in. When I remove the sd the logo appears. I have uninstalled the chip and it won't boot. Please any help?

I have installed many and this has never happened to me, the installation is perfect

 

[abal1000x]

after installing picofly it shows a black screen when an SD card is plugged in. When I remove the sd the logo appears. I have uninstalled the chip and it won't boot. Please any help?

I have installed many and this has never happened to me, the installation is perfect

You're not sourcing the 3.3v from sdcard line right?

 

[o0SaN0o]

You're not sourcing the 3.3v from sdcard line right?

if I have the 3.3v on that line

 

[abal1000x]

if I have the 3.3v on that line

You'll got that issue.