Hacking Hardware Picofly - a HWFLY switch modchip

[SQc04]

Im ready add firmware to the chip... But still not soldring to v1 nintendo switch.. It well blinking blue lite to white blue then green.

Green should be normal,The first boot will flash white

 

[Thegribbs]

Had the same idea. I ordered some 150n03ld (sop8, easier to test) a couple of weeks ago, still waiting on them.

Looks a bit easier than the TSMT-8 package. Really, I just wanted to order 20 flex cables, but the shipping times just aren't working. Hand soldering will do in the meantime.
I'm happy with anything that isn't on the scale of the DSBGA chip I had to dead bug last year

 

[Danook28]

Green should be normal,The first boot will flash white

Yes befor i add firmware it was red to green or green to red. After add 2.67 firmware it show blue to white blue lite. Thank you for more info.. Next day i well soldring it on v1 and good look..

 

[Flaviocarvalho]

I f**** up my console...wanna know if is there any chance i can isolate the pad from the circuit... the left one is shorted and the right one is not getting continuity to the resistor...so i screwed everything ahhaha.... i will use it as learning board...want to know if i can cut the trail that comes from emmc to the left pad (the one that is shorted) and cut the trail that goes from right pad to the resistor (the one that is not getting continuity). Isolate this point and reball the emmc jumping directly from there to the end of the trail (resistor). I tried to draw. The blue stripes is the trail i wanna cut. Thanks and sorry for the long text

 

[Othmenchargui]

Hi . I want to know if anyone tried to cut raspberry pi pico. because I only found Raspberry in my country

 

[rehius]

Hi . I want to know if anyone tried to cut raspberry pi pico. because I only found Raspberry in my country

works fine, at least 3 people have tested that already. check pico soldering example in the main post.
cut is required only to fit inside, you can test it without cutting firstly

 

[Othmenchargui]

works fine, at least 3 people have tested that already. check pico soldering example in the main post.
cut is required only to fit inside, you can test it without cutting firstly

Thank my friend
I have a question about mosfet
No type is sold in my country no equivalent
I have a lot motherboard
For example i have this work or no

 

[MegaDeKay]

FYI, it sounds like Nintendo is issuing DMCA takedown requests for Lockpick and maybe other Github repositories as well. Time to fire up "git clone" on a number of repos, I guess???

 

[QuiTim]

Thank my friend
I have a question about mosfet
No type is sold in my country no equivalent
I have a lot motherboard
For example i have this work or no

Yes, this should work

 

[789-Benny]

FYI, it sounds like Nintendo is issuing DMCA takedown requests for Lockpick and maybe other Github repositories as well. Time to fire up "git clone" on a number of repos, I guess???

fuck nintendo

 

[handsom_tomato]

 

[789-Benny]

Green should be normal,The first boot will flash white

Your flex cable design has errors when exporting gebber file?

Have put it into jlspcb will see what they come back with after the review. Seems like it's a short across pads and then tracks

 

[bilalhassan341]

FYI, it sounds like Nintendo is issuing DMCA takedown requests for Lockpick and maybe other Github repositories as well. Time to fire up "git clone" on a number of repos, I guess???

So, we cannot dump our own keys from the consoles.

 

[Flaviocarvalho]

I f**** up my console...wanna know if is there any chance i can isolate the pad from the circuit... the left one is shorted and the right one is not getting continuity to the resistor...so i screwed everything ahhaha.... i will use it as learning board...want to know if i can cut the trail that comes from emmc to the left pad (the one that is shorted) and cut the trail that goes from right pad to the resistor (the one that is not getting continuity). Isolate this point and reball the emmc jumping directly from there to the end of the trail (resistor). I tried to draw. The blue stripes is the trail i wanna cut. Thanks and sorry for the long text

Any help?

 

[Interceptor777]

So I've read through a lot of posts here and can't find any info on running atmosphere after it was found the unlock file stopped booting OFW. Is it still possible with 2.67? I know the older firmware is posed but I highly doubt downgrading is a good idea. It's a bit annoying I can't run the homebrew I want, it is my console after all :/

 

[SQc04]

View attachment 369181

Your flex cable design has errors when exporting gebber file?

Have put it into jlspcb will see what they come back with after the review. Seems like it's a short across pads and then tracks

This is because I forgot to set the DRC rule, change the rule to 0 and that's it

 

[NooBziN]

View attachment 368794

Do you have a photo of it installed?

 

[SQc04]

Do you have a photo of it installed?

 

[Interceptor777]

2nd successful attempt at two MOSFETs. Fixed my flashes green but boots OFW issue. I don't think it was the MOSFETs failing, it was the source ground connection, it didn't have a good connection with the pad on the SoC. I cannot get solder to stick to that pad so I just grounded it on the shielding and it works well now.

 

[NooBziN]

View attachment 369219
View attachment 369220
View attachment 369221

only MOSFET
no flex cable