Yes it's been working unofficially droma couple of weeks ago using my GitHub's master. Only my laziness during the holidays prevented me from releasing the new version.With DLC ?
It does. But you'll have the infamous message for some dlcs.They'll work but say they are icomplete and they need to redownload or something like that. They'll still work if you ignore the message.Ooooooh yeah.
SX OS 2.5.1 adds support for installing XCI.
Will be interesting, if that works good with the selfbuild XCIs including Updates or/and DLCs.
The message will only show when you install them in a system that is in a firmware equal or higher than 6.0
Dunno, didn't look into it yet since I mostly use xci and was in 5.1 till recently and 5.1 doesn't have that issue. The easier way would be in the CFW side in my opinion.Is that fixable somehow ? Or are new updated DLC files needed ?
I have this message-problem only with Overcooked 2.
When are you releasing it, I don't know how to compile that :vYes it's been working unofficially droma couple of weeks ago using my GitHub's master. Only my laziness during the holidays prevented me from releasing the new version.
It does. But you'll have the infamous message for some dlcs.They'll work but say they are icomplete and they need to redownload or something like that. They'll still work if you ignore the message.
The message will only show when you install them in a system that is in a firmware equal or higher than 6.0
When are you releasing it, I don't know how to compile that :v
Yes, it's as Sonic says. It's in the v0.79 in the first post has the Xenoblade fix.When are you releasing it, I don't know how to compile that :v
ok so i have 3 games that refuse to show an icon and dont mount as xci files lost in harmony ,aca puzzle bubble and aaero complete addition to convert the nsp to xci i have used this method
manual mode by dpouble clicking the bat
option 1
load nsp and press enter
Input "1" to start processing
Input "2" to repack list as xci
Input "1" to "PATCH" the Required System Version
Input "5" to change the keygeneration to 5 (FW 5.0.0-5.1.0)
in sx instller puzzlebubble shows but says unable to get metadata however the other two games dont show there and are converted in the same way
Would need to check those games, Aero and Puzzle seem to be keygeneration6 so you would need to have masterkey5 to decrypt them then lost in harmony seem to be keygeneration5 (masterkey4) so i believe you should be god with that one.so any ideas about this ?
Pang Adventures [010087300B730000][v0].nsp
the game crashed when started
nsp to xci
edit:
The game is probably a bad dump, it also does not work as nsp
It Not run for me in in airplane mode.No, it works fine. BUT ... you must be in airplane mode.
What about 6.2.0 ? And I use SXOS 2.5.1 !It Not run for me in in airplane mode.
You tried converting with 4nxci, I am right? 4nxci re-encrypts the files that's why it takes so much time making the nca, also it rehashes the nca and changes it's names. I don't rehash the files except when I patch the cnmt to diferentiate it from the original one, though I may stop renaming it.@JRoad
I tested to install a XCI with the new SXOS 2.5.1. Works fine. (But it has a sad bug with "delete after install".)
I made a NSP out of the same game and tried to install it aswell.
Strangely, what I've noticed: SXOS doesn't tell that it's already installed but starts installation.
I've seen that the contained NCAs of the 2 files (XCI and NSP) have different names.
Is that why the Switch thinks it's a different game?
Where will it be installed. In the same folder, so the size will be doubled?
I hope that'll not lead to a big error.
You tried converting with 4nxci, I am right? 4nxci re-encrypts the files that's why it takes so much time making the nca, also it rehashes the nca and changes it's names. I don't rehash the files except when I patch the cnmt to diferentiate it from the original one, though I may stop renaming it.