I can´t see any purple lines on the image I`ve attached. You mean same as Bad and Abal? Using APU shield as ground point?
BTW, Can I use APU shield too soldering the GND point of RP2040? In the past I modded one Lite and the ground point at the capacitor scares me a little bit hahaha
I can´t see any purple lines on the image I`ve attached. You mean same as Bad and Abal? Using APU shield as ground point?
BTW, Can I use APU shield too soldering the GND point of RP2040? In the past I modded one Lite and the ground point at the capacitor scares me a little bit hahaha
Thank you so much. I´m waiting on UV Mask and B7000 glue to mod another two lites. I prefer flex mode in APU but using mosfets is cheaper and needs more patience (and I prefer it haha)
The chip does not wake the console. This is a well known RTC auto power on after shutdown used by N system. Every Switch console automatically turns on after poweroff from the Horizon OS, even the unmodded ones.
The picofly firmware detects that and automatically shuts the system down after the successful glitch.
v2.0 + Active MMC communication
v2.1 + Toshiba support
v2.2 + Fix Toshiba boot fail
v2.3 + SanDisk support
v2.4 + Faster Toshiba boot
v2.5 + fix OFW boot
v2.6 + software update, xiao & itsy support
v2.61 + Instinct-NX sdloader, bug fixes
v2.62 + Make 16.0.1 happy (fix OFW boot)
v2.63 + roll back some 2.62 boot speed tricks
v2.64 + enable back the board detection
v2.65 + RP Pico support, double reset removed
v2.66 + Bypass to OFW after update for proper fuse burning
v2.67 + Don't bypass to OFW on first install
v2.70 + new LED indication, i2c undervoltage hack
v2.71 + support for SQc open-source board
v2.72 + disable CLK check, it's unstable
v2.73 + add LED signal on success
v2.74 + 300 mhz precision
= is long pulse, * is short pulse:
= USB flashing done
** RST is not connected
*= CMD is not connected
=* D0 is not connected
== CLK is not connected
*** No eMMC CMD1 responce (bad eMMC?)
**= No eMMC block 1 read (should not happen)
*=* No eMMC block 0 read (eMMC init failure?)
*== No eMMC CMD1 request (poor wiring, or dead CPU)
=** eMMC init failure during glitch process
=*= CPU never reach BCT check, should not happen
==* CPU always reach BCT check (no glitch reaction, check mosfet)
=== Glitch attempt limit reached, cannot glitch
If your glitch is unstable (==* error), and the proper boot happens only when you press Reset after joycon logo, you can add two more wires to make glitch much better.
Q: rp2040 boards support
A: WaveShare 2040-zero/one, xiao-rp2040, adafruit itsybitsy (Pi Pico is not supportedfor now)
Q: GREEN, but instant reset
A: Clean flux near the RST point
Q: Do I really need 47 Ohm resistors?
A: You can skip them, however in this case you will have to use emuMMC due to the line interference, sysNAND would not boot (sysNAND data can be damaged).
Q: Does the firmware has learning? How to reset statistics
A: Short pin 0 to either 1 or GND during start for chip reset. The statistics is collected each boot. The more you start it - the better it boots.
v2.5 firmware had a bug with BOOT0 corruption. To recover it:
- boot "Full Stock" using hekate
- update to the latest official firmware over Wi-Fi
- boot "Full Stock" using hekate
- perform a full system reset
- show firmware information
- update firmware from SD card (place update.bin into the root folder)
- rollback to the backup firmware slot
- reset learning statistics
- dump / write sdloader
if you have an rp2040-zero from waveshare/ali then it has a neopixel. It is used for diagnosing proper firmware flashes as well as console glitching. If you plug it in, and flash the uf2 firmware to it and immediately see a red light after flashing (this is not the same as flashing, then unplugging and replugging), then no rgb jumper needs to be made. If on the other hand, you get one quick green flashing light, then you need to bridge the jumper pads indicated to swap the LED colors for proper diagnoses capability.
hello, after the chip will work (thanks to the forum for helping me) I have problems starting sysnand, purple screen and error in hekate, do you think that placing the 2 resistors in Dat0 and CMD can solve it or just damage my Emmc permanently? before placing the chip the Emmc worked correctly.
hello, after the chip will work (thanks to the forum for helping me) I have problems starting sysnand, purple screen and error in hekate, do you think that placing the 2 resistors in Dat0 and CMD can solve it or just damage my Emmc permanently? before placing the chip the Emmc worked correctly.
Hello, a little update, I put the 2 resistors in Dat0 0 and CMD, I reset the chip and there was a change in the information displayed and I even dared to try to create the emunand but in the end it said the same thing "Emmc slowmode" or something like that. burn my emmc?
hello, after the chip will work (thanks to the forum for helping me) I have problems starting sysnand, purple screen and error in hekate, do you think that placing the 2 resistors in Dat0 and CMD can solve it or just damage my Emmc permanently? before placing the chip the Emmc worked correctly.
Post automatically merged:
Hello, a little update, I put the 2 resistors in Dat0 0 and CMD, I reset the chip and there was a change in the information displayed and I even dared to try to create the emunand but in the end it said the same thing "Emmc slowmode" or something like that. burn my emmc?
hello, thanks for your answer, I replaced the resistor set although it was correct, in the measurement it marked 47ohms the same as those of clk and dat0, I replaced the one that was set with 2 of 47ohms and I obtained the results that you see in the answer in my post , a bit of info on the emmc although still with errors
hello, thanks for your answer, I replaced the resistor set although it was correct, in the measurement it marked 47ohms the same as those of clk and dat0, I replaced the one that was set with 2 of 47ohms and I obtained the results that you see in the answer in my post , a bit of info on the emmc although still with errors
I hope we mean the same resistor. I'm talking about the cmd resistor located on the motherboard. The one that causes pink screen on oleds. If you don't know where it is, go a few pages back.
I hope we mean the same resistor. I'm talking about the cmd resistor located on the motherboard. The one that causes pink screen on oleds. If you don't know where it is, go a few pages back.
Thank you, I hadn't understood, but I understand it now, you mean this resistor in the photo, I'm going to look for a replacement and I'll tell you if it works
Thank you, I hadn't understood, but I understand it now, you mean this resistor in the photo, I'm going to look for a replacement and I'll tell you if it works
Thank you, I hadn't understood, but I understand it now, you mean this resistor in the photo, I'm going to look for a replacement and I'll tell you if it works
@jmmc I hope you did not follow my advice and bought from a different store... I just received a second batch from that seller, they're selling the shitty "OATO" adapters without changing the original advertisement. First batch was good, this one goes directly into trash.
@jmmc I hope you did not follow my advice and bought from a different store... I just received a second batch from that seller, they're selling the shitty "OATO" adapters without changing the original advertisement. First batch was good, this one goes directly into trash.
And this is why hwfly and other Chinese based Mods are dying. We're sick of the lies and disengenuous money hungry crap. This story makes me want to invest in emmc stencils and be done with adaptors all together.
@jmmc I hope you did not follow my advice and bought from a different store... I just received a second batch from that seller, they're selling the shitty "OATO" adapters without changing the original advertisement. First batch was good, this one goes directly into trash.
And this is why hwfly and other Chinese based Mods are dying. We're sick of the lies and disengenuous money hungry crap. This story makes me want to invest in emmc stencils and be done with adaptors all together.
Actually no, I was thinking of the "black" version, I imagine it should be similar to the old "corner" adapter. If so, it has a good contact, but I haven't tested them personally.
There should be as well good adapters from "official HWfly stores", but it's over 10 EUR each, so stencil + hot air is the way.
Hello, a little update, I put the 2 resistors in Dat0 0 and CMD, I reset the chip and there was a change in the information displayed and I even dared to try to create the emunand but in the end it said the same thing "Emmc slowmode" or something like that. burn my emmc?
hello, after the chip will work (thanks to the forum for helping me) I have problems starting sysnand, purple screen and error in hekate, do you think that placing the 2 resistors in Dat0 and CMD can solve it or just damage my Emmc permanently? before placing the chip the Emmc worked correctly.
Post automatically merged:
Hello, a little update, I put the 2 resistors in Dat0 0 and CMD, I reset the chip and there was a change in the information displayed and I even dared to try to create the emunand but in the end it said the same thing "Emmc slowmode" or something like that. burn my emmc?
you don't need to put more than 1 resistor even more CMD does not help at all only 1 in each necessary if you have a slowness problem redo the solder cleaning
honestly where did you see this guide lol
A new Nintendo Switch firmware update is here. System software version 18.0.1 has been released. This update offers the typical stability features as all other...
With Apple having recently updated their guidelines for the App Store, iOS users have been left to speculate on specific wording and whether retro emulators as we...
TheFlow has done it again--a new kernel exploit has been released for PlayStation 4 consoles. This latest exploit is called PPPwn, and works on PlayStation 4 systems...
The time has finally come, and after many, many years (if not decades) of Apple users having to side load emulator apps into their iOS devices through unofficial...
While rumors had been floating about rampantly as to the future plans of Nintendo, the President of the company, Shuntaro Furukawa, made a brief statement confirming...
Nintendo might just as well be a law firm more than a videogame company at this point in time, since they have yet again issued their now almost trademarked usual...
Another video game prototype has been found and preserved, and this time, it's none other than the game that spawned an entire franchise beloved by many, the very...
As each year passes, retro games become harder and harder to play, as the physical media begins to fall apart and becomes more difficult and expensive to obtain. The...
Anbernic is back with yet another retro handheld device. The upcoming RG28XX is another console sporting the quad-core H700 chip of the company's recent RG35XX 2024...
Nintendo has officially announced that a successor to the beloved Switch console is on the horizon. As we eagerly anticipate what innovations this new device will...
Nintendo has officially announced that a successor to the beloved Switch console is on the horizon. As we eagerly anticipate what innovations this new device will...
While rumors had been floating about rampantly as to the future plans of Nintendo, the President of the company, Shuntaro Furukawa, made a brief statement confirming...
Nintendo might just as well be a law firm more than a videogame company at this point in time, since they have yet again issued their now almost trademarked usual...
With Apple having recently updated their guidelines for the App Store, iOS users have been left to speculate on specific wording and whether retro emulators as we...
The time has finally come, and after many, many years (if not decades) of Apple users having to side load emulator apps into their iOS devices through unofficial...
As each year passes, retro games become harder and harder to play, as the physical media begins to fall apart and becomes more difficult and expensive to obtain. The...
A new Nintendo Switch firmware update is here. System software version 18.0.1 has been released. This update offers the typical stability features as all other...
TheFlow has done it again--a new kernel exploit has been released for PlayStation 4 consoles. This latest exploit is called PPPwn, and works on PlayStation 4 systems...
After rumour got out about an upcoming NES Edition release for the famed Nintendo World Championships, Nintendo has officially unveiled the new game, titled "Nintendo...
DOOM is well-known for being ported to basically every device with some kind of input, and that list now includes the old retro game console in Persona 5 Royal...