Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

[Hayato213]

no i lend my switch to a friend and he updated it now the vol buttons dont work on hos (cfw) but i have a backup of my old uf2...i forgot how to enter update mode

--------------------- MERGED ---------------------------



thx...i have a button on the chip

https://github.com/euclala/RCM-X86

Instruction is here, you need a magnet apparently for the RCM X86.

 

[Space_Goddess_Samus_Aran]

i entered uf 2 with buttonpress....i put back my backup but now it blinks red and wont let me exit uf 2 mode

 

[Hayato213]

i entered uf 2 with buttonpress....i put back my backup but now it blinks red and wont let me exit uf 2 mode

Hard boot it force it to shut off by holding the power button for like 20 seconds.

 

[Space_Goddess_Samus_Aran]

ok... weird is mattytrog installed it for me and told me its an rcm x86....but if i look on it it has abutton and says Triket M0..but the file on its storage says RCM_x86.UF2

 

[Hayato213]

ok... weird is mattytrog installed it for me and told me its an rcm x86....but if i look on it it has abutton and says Triket M0..but the file on its storage says RCM_x86.UF2

It is basically a trinket, as it is a clone of it

 

[Space_Goddess_Samus_Aran]

i tried it with hard reset but as soon as i pres powerbutton it goes blinking red again

 

[Hayato213]

i tried it with hard reset but as soon as i pres powerbutton it goes blinking red again

Try flashing it again, probably it didn't finish.

 

[Space_Goddess_Samus_Aran]

ok

 

[Space_Goddess_Samus_Aran]

i flashed it again (i flashed the backup i made today thats why it didnt worked)
i made a backup of the uf2 which was on the chip when mattytrog shipped my switch back.....if i flash an updaed uf2...then only the vol+ works under fusee gelee..in hos no vol button works) but if i flash the backup i made when the switch arrived from mattytrog on it they work like normal

 

[c3s]

does this work on fw 10.2.0

 

[Hayato213]

does this work on fw 10.2.0

Work on unpatched unit all firmware.

 

[c3s]

i have installed rcmx86 v2.0 when i connect the switch to pc thru usb i get a message that says that are problems with the usb drive .
i have soldered the rcmx86 off again and then there is no problems any ideas on what is wrong

 

[zerofo]

i have installed rcmx86 v2.0 when i connect the switch to pc thru usb i get a message that says that are problems with the usb drive .
i have soldered the rcmx86 off again and then there is no problems any ideas on what is wrong

the same issue...with the black pcb version.... on the newest uf2 firmware or the oldest sxos version.

just use the old version uf2(like v133 can make rcm x86 sleep. ), i rebuild one for sxos payload.

because the hekate payload sometime can't boot into sxos on the v133).

And double click can't connect to the PC with bootloader mode ( i get the same issue as you say , may any version like the oldest/ newest/v133)

 

[c3s]

i have tryed to use the magnet but i cant get it to work is there a better way to do this othere than a magent ???

 

[Hayato213]

i have tryed to use the magnet but i cant get it to work is there a better way to do this othere than

That chip need a magnet. Other chip like Trinket M0 doesn't, I would check the GND pin make sure the connection is good.

 

[Alexstill]

Hey all
so I installed a RCM-x86 2.0 swith is on 11.0 and am using SXOS 3.1.0 I get the red Nintendo boot Screen i get SXOS boot screen i get black screen with white Nintendo then am stuck in a black screen I have to hold the power and + and try again then it works this is every time any ideas how to fix this ?
thank you

 

[c3s]

That chip need a magnet. Other chip like Trinket M0 doesn't, I would check the GND pin make sure the connection is good.

the chip itself works great so the gnd pin works just fine

 

[Hayato213]

the chip itself works great so the gnd pin works just fine

Ground Pins affect pc connection when you try to flash the uf2 , alteast according to what Mattytrog said in the past.

 

[zerofo]

i have tryed to use the magnet but i cant get it to work is there a better way to do this othere than a magent ???

this should work fine with MTP (like .DBI,mtpserver..) on SXOS, but without bootloader mode (you must solder it off to use bootloader).

 

[zerofo]

Hey all
so I installed a RCM-x86 2.0 swith is on 11.0 and am using SXOS 3.1.0 I get the red Nintendo boot Screen i get SXOS boot screen i get black screen with white Nintendo then am stuck in a black screen I have to hold the power and + and try again then it works this is every time any ideas how to fix this ?
thank you

i think i reported an same issue on FUSEE_SUITE's Repo,
it should be also fix on the old version or the file at Reply#479