search google for Murata DLM0NSN900HY2
Any idea where I can get this part? I can only find it on eBay (got it right after your message -- still waiting for it to arrive). Are any other compatible alternatives?
search google for Murata DLM0NSN900HY2
Any idea where I can get this part? I can only find it on eBay (got it right after your message -- still waiting for it to arrive). Are any other compatible alternatives?
I got mine from farnell can you not order from them in your country
I couldn't source it from companies here. I just found out about Farnell Export (https://export.farnell.com/) and they ship with UPS at only 5 pounds. I just made an order for 10, fingers crossed.What electronics companies have you got in greece
I am used to it and it works perfectly.
https://ro.mouser.com/ProductDetail/Panasonic/EXC-24CS350U?qs=sGAEpiMZZMsVJzu5wKIZCVmiNDXvL6WFCSe53ELiIcQ=
So i the part finally arrived and was able to change the choke coil. Problem is dock still doesn't work. Also i manage to detach a small capacitor like smd part while using a dmm checking for continuity its near one of the choke chokes it look like a ceramic super tiny, anybody know where i can get one?
If you've knocked one of the capacitors of on the signal lines it won't work, if this is the case there 0.1uf
i knocked off the capacitor after testing the dock, while doing continuity. so i guess it has nothing to do with my switch refusing to dock. so where can i get one of those capacitors and what is the size ? also what else could i check, was also wondering if it could be the charge port? since that what caused all the problem in the first place. maybe the charge port was soldered incorrectly ? is there a way to check ?
Maybe the capacitor wasn't on well after your previous repairs, as there not usually that easy to knock off with multimeter probes.
There just standard mlcc caps every good electronics company will have them, size is 0603 metric or 0201 imperial
You need to test that you've got continuity from the port to the coils or the point on the caps closest to the coils, this is not easy as its difficult to get at the pins on the usb connector, but with a very fine needle soldered to your probe tip you can just get in between the port and the pcb, the only other way is to purchase a male usb connector to insert into the usb receptacle then test from the pins to the coils.
ok so i was able to talk to a local electronic supplier. all they have is 0.1uf 0603 16v ? will this work ?
As long as the size is ok and there not 0603 imperial they will be fine
I couldn't source it from companies here. I just found out about Farnell Export (https://export.farnell.com/) and they ship with UPS at only 5 pounds. I just made an order for 10, fingers crossed.
Hi guys, a little advice needed if you can please, i have a switch that came in today and it charges ok but when you turn the charger round it doesn't, is also does not work in dock. I have tried new chargers and dock but still the same {all original} so i replaced charge port but still the same only charging on one side. Any ideas ? maybe m92t36 chip ? Thanks
Hi guys, a little advice needed if you can please, i have a switch that came in today and it charges ok but when you turn the charger round it doesn't, is also does not work in dock. I have tried new chargers and dock but still the same {all original} so i replaced charge port but still the same only charging on one side. Any ideas ? maybe m92t36 chip ? Thanks
Hello @Canna!
To the op... Does the console go into RCM?
If not, check pin 5 vcc on m92t36. Plug in to charger. Between 3 - 6v, power detector working, chip likely to be ok. Or that part of it is. Suspect bq24193.
If vcc in voltage is out of these voltages, with Nintendo charger plugged in, suspect m92t36.
If you can enter RCM, try sending Hekate. With usb unplugged... Make a note of battery level. Power off. Reboot... Back to hekate. Check again. If battery level not fairly consistent... Or you are getting 103% battery or something...
Or
Switch won't boot past switch logo...
Suspect bq24193.
Let me know if you need any more help