Yes.
I have the dualboot installation (joycon strap only) plus usb strap.
I'm with SXOS (6.2.0 emunand, 2.6.2 beta)... Should I have to test with 7.0.1???
Last edited by josete2k,
Yes.
I have the dualboot installation (joycon strap only) plus usb strap.
I'm with SXOS (6.2.0 emunand, 2.6.2 beta)... Should I have to test with 7.0.1???
v1.3.2 online.
The strap goes from the testpoint next to BQ24193 to pin 2... Near the battery connector.
If you don`t have it, you don`t have it.
The strap goes from the testpoint next to BQ24193 to pin 2... Near the battery connector.
If you don`t have it, you don`t have it.
https://gbatemp.net/threads/interna...ybitsy-m0-express-guide-files-support.508068/
Check that install guide, find your chip, it's on of the easy installs.
That guide also explains why the usb strap is used.
--------------------- MERGED ---------------------------
Do the alternate vol+ on the flex ribbon it works a treat.
--------------------- MERGED ---------------------------
Yeah I'm gonna disconnect mine when i get a chance.
Well I'm on OFW for online play so I need dualboot.
If I want to autoboot to emunand I can install autorcm... Due the usb strap the system always power off without any issue.
okay , can i install the point nr 2 to thr usb solder point on switch motherboard which is on diagramm too see ?
for what is the usb strap good ? can i add a external HDD to the hdmi converter ?
or for what is the usb strap good
greets
kermit84
--------------------- MERGED ---------------------------
for what is the usb strap good ? can i add a external HDD to the hdmi converter ?
or for what is the usb strap good
greets
kermit84
--------------------- MERGED ---------------------------
okay , can i install the point nr 2 to thr usb solder point on switch motherboard which is on diagramm too see ?
I have the method 3 soldering works the usb trap too ?
for what is the usb strap good ? can i add a external HDD to the hdmi converter ?
or for what is the usb strap good
greets
kermit84
@mattytrog for simpletons like me, what file do i need just for an external dongle? Ideally i need it so you just simply plug the dongle in upon booting into RCM and it boots firmware. Is this possible? As currently i have to boot it, then press the switch for it to push the payload. (Video below is: Switch turned off, plug dongle in, then press power button and boots into auto RCM, then press switch - no idea why the custom bootlogo glitches at the end?)
Last edited by metaljay,
Yes it's possible. Don't know the pinouts. Try the dragoninjector version. Let me know
Or generic trinket version
I'm trying to update to the latest version but i can't get to switchboot in horizon os. Now i'm trying the SAMD chip update mode but i get the following error: error (5) creating file bootloader/payloads/dummy. Any advice?
I remember you showing me the dongle you made yourself, was that a trinket?
edit: just tried the standard ones from @evilsperm (https://github.com/Aboshi/SwitchME/tree/master/UF2_SwitchME_Payloads) and they work instantly.
Hopefully you can extract the pins from this so I can use simple uf2 on my friends dongle
Last edited by metaljay,
Is it a bug when its only stay usb strap = ON ?
There was on my diagram joycon strap soldered too , but it stays obly usb strap is on , the usb strap is soldered .
Is it normal ? must i not get 2x Yes for USB and For Joycon Strap ?
Greets
Kermit84
There was on my diagram joycon strap soldered too , but it stays obly usb strap is on , the usb strap is soldered .
Is it normal ? must i not get 2x Yes for USB and For Joycon Strap ?
Greets
Kermit84
Yes. It will only update when it detects the straps. So, because you need to boot to Nintendo firmware to activate the strap, try booting with a joycon connected... Next reboot, status updated.
Press volume+ at and point... Reboot... Updated.
See? When the strap senses it is being used, it updates.
Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy
I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .
Thx for every helps
greets
kermit84
--------------------- MERGED ---------------------------
Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy
I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .
Ahh i was flashed the Trinket , Rebug , Current.UF2 , must i use other one when i install every strap ?
Thx for every helps
greets
kermit84
The vol+ strap is for booting cfw. It also has other options based on how long you hold vol+ down for. I will make a list of all the options tomorrow. I forgotten.Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy
I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .
Thx for every helps
greets
kermit84
--------------------- MERGED ---------------------------
If using a trinket m0, you will see a blue light through the grilles of your Switch when you press vol+.
ok your hurting my head a lot. i go away for 3 weeks, come back and it all different every single time.......
TRINKET_LEGACY3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
TRINKET_METHOD3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
which are these do i use on method 3 you did AGES ago for me (after i screwed it)
want the latest as im thinking about updating switch again to v8 from v6 obviously im running an old hekate and figured i better get the latest of that working first, then the new sd files then update firmware.
how terrible am i? i cant even get passed the first step hahaha.
TRINKET_LEGACY3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
TRINKET_METHOD3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
which are these do i use on method 3 you did AGES ago for me (after i screwed it)
want the latest as im thinking about updating switch again to v8 from v6 obviously im running an old hekate and figured i better get the latest of that working first, then the new sd files then update firmware.
how terrible am i? i cant even get passed the first step hahaha.
All you need to do is update the UF2. Double-press reset, drag and drop. Job done.
Similar threads
- No one is chatting at the moment.
-
-
-
-
-
-
-
-
-
-
-
@
Veho:
It's not like they're complaining that their Slurpee is 99% ice or something, but if the cocktail calls for "shot of vodka, shot of vermouth, shot of gin, shot of Campari, three shots of juice, squirt of lemon" and ends up being a thimbleful of booze, that's a problem. -
@
The Real Jdbye:
the funny thing is cocktails in norway are only allowed to have 1 20ml shot of booze -
-
-
-
-
@
The Real Jdbye:
but you could buy as many shots of whisky (or anything else) as you want and ask for a glass of ice and pour them in
-
-
-
@
Veho:
There was a comparison of the number of Ibuprofen poisonings before and after they limited the maximum dosage per box or per pill (i'll look that up). No limit on the number of boxes you can still buy as many as you want, so people argued it was pointless.
-
@
Veho:
But the number of (accidental) poisonings dropped because drinking an entire package of ibuprofen pills went from "I need a new liver" to "I need a new box of Ibuprofen".
-
@
Veho:
Here we have ketoprofen that used to be prescription-only because of the risk of toxic dosages, but then they halved the dose per pill and sell them in bottles of six pills apiece instead of twenty and it doesn't need a prescription any more. Yes you can buy more than one bottle but people simply don't.
-
@
Psionic Roshambo:
Usually accidentally overdose of ibuprofen here is from people taking like cold medicine then ibuprofen for a headache and the combination is over what they need -
-
