Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

[josete2k]

do you have usb straps installed?

Yes.

I have the dualboot installation (joycon strap only) plus usb strap.

I'm with SXOS (6.2.0 emunand, 2.6.2 beta)... Should I have to test with 7.0.1???

 

[madturbo123]

nah it's cool

Yes.

I have the dualboot installation (joycon strap only) plus usb strap.

I'm with SXOS (6.2.0 emunand, 2.6.2 beta)... Should I have to test with 7.0.1???

Nah it' all good thanks. I'll un-solder the strap see how it goes.

 

[kermit84]

josete2k where are the usb straps to install on diagramm ?

I havent found this here ? is it on the extern HDMi module ? For what are the usb straps ?

Greets

 

[mattytrog]

v1.3.2 online.

The strap goes from the testpoint next to BQ24193 to pin 2... Near the battery connector.

If you don`t have it, you don`t have it.

 

[madturbo123]

josete2k where are the usb straps to install on diagramm ?

I havent found this here ? is it on the extern HDMi module ? For what are the usb straps

Greets

https://gbatemp.net/threads/interna...ybitsy-m0-express-guide-files-support.508068/

Check that install guide, find your chip, it's on of the easy installs.

That guide also explains why the usb strap is used.

--------------------- MERGED ---------------------------

Yes.

I have the dualboot installation (joycon strap only) plus usb strap.

Do the alternate vol+ on the flex ribbon it works a treat.

--------------------- MERGED ---------------------------

v1.3.2 online.

The strap goes from the testpoint next to BQ24193 to pin 2... Near the battery connector.

If you don`t have it, you don`t have it.

Yeah I'm gonna disconnect mine when i get a chance.

 

[josete2k]

https://gbatemp.net/threads/interna...ybitsy-m0-express-guide-files-support.508068/

Do the alternate vol+ on the flex ribbon it works a treat.

Well I'm on OFW for online play so I need dualboot.

If I want to autoboot to emunand I can install autorcm... Due the usb strap the system always power off without any issue.

 

[kermit84]

okay , can i install the point nr 2 to thr usb solder point on switch motherboard which is on diagramm too see ?

for what is the usb strap good ? can i add a external HDD to the hdmi converter ?

or for what is the usb strap good

greets
kermit84

--------------------- MERGED ---------------------------

okay , can i install the point nr 2 to thr usb solder point on switch motherboard which is on diagramm too see ?

I have the method 3 soldering works the usb trap too ?

for what is the usb strap good ? can i add a external HDD to the hdmi converter ?

or for what is the usb strap good

greets
kermit84

 

[metaljay]

@mattytrog for simpletons like me, what file do i need just for an external dongle? Ideally i need it so you just simply plug the dongle in upon booting into RCM and it boots firmware. Is this possible? As currently i have to boot it, then press the switch for it to push the payload. (Video below is: Switch turned off, plug dongle in, then press power button and boots into auto RCM, then press switch - no idea why the custom bootlogo glitches at the end?)

 

[mattytrog]

@mattytrog for simpletons like me, what file do i need just for an external dongle? Ideally i need it so you just simply plug the dongle in upon booting into RCM and it boots firmware. Is this possible? As currently i have to boot it, then press the switch for it to push the payload. (Video below is: Switch turned off, plug dongle in, then press power button and boots into auto RCM, then press switch - no idea why the custom bootlogo glitches at the end?)

Yes it's possible. Don't know the pinouts. Try the dragoninjector version. Let me know
Or generic trinket version

 

[PSxed]

I'm trying to update to the latest version but i can't get to switchboot in horizon os. Now i'm trying the SAMD chip update mode but i get the following error: error (5) creating file bootloader/payloads/dummy. Any advice?

 

[metaljay]

Yes it's possible. Don't know the pinouts. Try the dragoninjector version. Let me know
Or generic trinket version

I remember you showing me the dongle you made yourself, was that a trinket?

edit: just tried the standard ones from @evilsperm (https://github.com/Aboshi/SwitchME/tree/master/UF2_SwitchME_Payloads) and they work instantly.
Hopefully you can extract the pins from this so I can use simple uf2 on my friends dongle

 

[mattytrog]

I'm trying to update to the latest version but i can't get to switchboot in horizon os. Now i'm trying the SAMD chip update mode but i get the following error: error (5) creating file bootloader/payloads/dummy. Any advice?

Is SD card ok? You have bootloader/payloads folder on SD?

 

[metaljay]

I was trying to show that can you copy the pin/files from what evilsperm uses so I can use your simple-UF2? Would much rather use your stuff my friend

 

[kermit84]

Is it a bug when its only stay usb strap = ON ?

There was on my diagram joycon strap soldered too , but it stays obly usb strap is on , the usb strap is soldered .

Is it normal ? must i not get 2x Yes for USB and For Joycon Strap ?

Greets
Kermit84

 

[mattytrog]

Is it a bug when its only stay usb strap = ON ?

There was on my diagram joycon strap soldered too , but it stays obly usb strap is on , the usb strap is soldered .

Is it normal ? must i not get 2x Yes for USB and For Joycon Strap ?

Greets
Kermit84

Yes. It will only update when it detects the straps. So, because you need to boot to Nintendo firmware to activate the strap, try booting with a joycon connected... Next reboot, status updated.

Press volume+ at and point... Reboot... Updated.

See? When the strap senses it is being used, it updates.

 

[kermit84]

Yes. It will only update when it detects the straps. So, because you need to boot to Nintendo firmware to activate the strap, try booting with a joycon connected... Next reboot, status updated.

Press volume+ at and point... Reboot... Updated.

See? When the strap senses it is being used, it updates.

Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy

I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .

Thx for every helps

greets
kermit84

--------------------- MERGED ---------------------------

Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy

I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .

Ahh i was flashed the Trinket , Rebug , Current.UF2 , must i use other one when i install every strap ?

Thx for every helps

greets
kermit84

 

[mattytrog]

Hollllyyyyyyy , thats method is reallly damn stable , the method 3 was realy little bit buggy

I have a question the vol + Strap is only for dual Booting without and when i solder volume + i every time boot cfw permanently or ? AUTORCM is offline .

Thx for every helps

greets
kermit84

--------------------- MERGED ---------------------------

The vol+ strap is for booting cfw. It also has other options based on how long you hold vol+ down for. I will make a list of all the options tomorrow. I forgotten.

If using a trinket m0, you will see a blue light through the grilles of your Switch when you press vol+.

 

[roamin]

ok your hurting my head a lot. i go away for 3 weeks, come back and it all different every single time.......

TRINKET_LEGACY3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
TRINKET_METHOD3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago

which are these do i use on method 3 you did AGES ago for me (after i screwed it)

want the latest as im thinking about updating switch again to v8 from v6 obviously im running an old hekate and figured i better get the latest of that working first, then the new sd files then update firmware.
how terrible am i? i cant even get passed the first step hahaha.

 

[mattytrog]

ok your hurting my head a lot. i go away for 3 weeks, come back and it all different every single time.......

TRINKET_LEGACY3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago
TRINKET_METHOD3_SWITCHBOOT_PART2_V132.UF2 v132 push. Old source remove. 22 hours ago

which are these do i use on method 3 you did AGES ago for me (after i screwed it)

want the latest as im thinking about updating switch again to v8 from v6 obviously im running an old hekate and figured i better get the latest of that working first, then the new sd files then update firmware.
how terrible am i? i cant even get passed the first step hahaha.

All you need to do is update the UF2. Double-press reset, drag and drop. Job done.

 

[roamin]

@mattytrog which one of the 2? legacy or method3?