It is possible. I haven`t written the function yet.i use a rebug chip.
and method 3.
only joycon strap connected :/
what is a good solution to change mode with only joycon strap or not possible?
Ok 0.9.8r2 tested. All is good apart from Power Off with SX OS. It still reboots in ArgonNX.
Hmmm... Needs a autohosoff routine adding to ArgonNX.
Dougie...Hi maybe i should put 1 in Hekate autohosoff ini ? I'm sure it's 0 yet.
Edit : forget what i said. Have to learn more
Fancy testing this?
Get into mode 3 (ArgonNX) and check it is powering off correctly. Should see a "Shutting down" screen.
Yeap with pleasure dude
Ok i will test the Power Off from Mode 3 ArgonNX and from SX OS Horizon after. Will give feedback asap...
BTW : i not abuse could make a separate UF2 with the DotStar brightness on Adafruit boards like before cause it's too much bright indeed i have a crystal case and makes me blind lol
--------------------- MERGED ---------------------------
Fancy Test done :
Powering Off from Mode 3 ArgonNX : it is powering off correctly from SX OS Horizon (with a shutting down screen after a while) and from ArgonNX Menu too
On the other hand if SD Removed i can't boot into Hekate with Vol-/power anymore...
A yellow message appears : " Failed to init SD card.....Press power button to reboot into RCM..."
Do you have your Trinket flashed? If blank or in bootloader mode, it will cause conflicts. I tested it (with nxUSB is it called? The one you can access your SD card) and worked without issue.I just installed with Trinket M0 (v0.9.8r2) and I'm having an issue where USB install with Goldleaf or Tinfoil does not work. Goldleaf hangs, whereas Tinfoil causes an error on the Switch. I know Goldleaf USB install worked prior to this installation. It seems like the Trinket is not properly disconnected from the USB lines when asleep. Is this issue documented?
Do you have your Trinket flashed? If blank or in bootloader mode, it will cause conflicts. I tested it (with nxUSB is it called? The one you can access your SD card) and worked without issue.
Deleted. Incomplete.Yes, I flashed it with Simple-UF2 and kept the original Trinket bootloader (no Switchboot). There are no Vol+ or Joy-Con wires. It injects the payload perfectly, but seems to cause USB issues otherwise. I can access the Trinket in bootloader mode and reflash it through the Switch's USB port.
Thanks for helping me troubleshoot this. I tried that UF2 image and the USB issue with TInfoil stopped. However, I put the 0.9.8r2 UF2 back on the Trinket and Tinfoil works now. I have no what changed.OK... Can you just try this for me? See if this fixes the issue? This is a UF2 file.
OK... The USB strap is to prevent being stuck in RCM.Thanks for helping me troubleshoot this. I tried that UF2 image and the USB issue with TInfoil stopped. However, I put the 0.9.8r2 UF2 back on the Trinket and Tinfoil works now. I have no what changed.
What exactly is the USB strap for? I couldn't find any clear description of what it does and I'd like to know in case it could be related to the problem.
Deleted. Didn`t work.It seems like my issue may have had more to do with my PC. Tinfoil threw an error when I was trying to install software from an external drive, but it does not when I try to install from the PC storage. As for Goldleaf, it still hangs, so I think that issue may be a bug in Goldlead itself. Thanks for the help.
Cheers Dave.Goldleaf USB install is still flakey af, for what it's worth.
I'm a little confused now. I got the same error with Tinfoil again even though it had been working (using the 0.9.8r2 UF2, not the test one you linked). Now, the Switch behaves as if the volume up button is always pressed, even though I did not connect a wire to it. I've fully powered it down, turned autoRCM off and on, but this issue persists. How can the volume button be "pressed" when the Trinket is only connected through USB? This almost seems like a software bug caused by shutting down after an error message.Just to rule it out, could you please test this UF2?
Rather than sleeping in host mode, the CTRLA bit for ENABLE is set to 0. This disabled the trinket USB interface completely until next power cycle.
OK. You have no "straps" connected...I'm a little confused now. I got the same error with Tinfoil again even though it had been working (using the 0.9.8r2 UF2, not the test one you linked). Now, the Switch behaves as if the volume up button is always pressed, even though I did not connect a wire to it. I've fully powered it down, turned autoRCM off and on, but this issue persists. How can the volume button be "pressed" when the Trinket is only connected through USB? This almost seems like a software bug caused by shutting down after an error message.
I uploaded the second USB-disable-UF2 you sent to see if it would change anything, but it wouldn't boot Hekate or anything else. My PC also couldn't see the Trinket in bootloader mode until I booted Horizon by sending a payload from my PC through USB.