What problem are you having Dougie?Ok dude thx. Gonna try to find what's going wrong or misunderstood by my side and trust me it could last lol
What problem are you having Dougie?Ok dude thx. Gonna try to find what's going wrong or misunderstood by my side and trust me it could last lol
What problem are you having Dougie?
It seems like a bad new Simple_V0.9.8.UF2 bad flash...Like nothing was upgraded...
But i can't be. Don't waste your time with me it's sure i missed something...I mean some Led's understanding/behaviour....
But it flashing so fast...
Just boot your switch while holding vol- (have a payload called "payload.bin" on SD root)
OK... What chip are you using dougie?Yeap pal. But that's not the problem as i mentionned upon this works.
For the file size still verified and it matches.
My problem with V0.9.8 is that the Mode's changing doesn't match the New Flowchart Led's Colour (behaviour)....
While the Payload's change seems to be ok.
Don't take care of my little pb. I'll figure it out. If not i'll post
OK... What chip are you using dougie?
Probably you have payload.bin as memloaderWell i think the better one the Trinket M0 ( others don't be upset not my mind). Yet i succeed to reach Mode 3 AgonNX but i pressed Power and showed onto Memloader
Probably you have payload.bin as memloader
OK... You are using a trinket.Ok. I'm now in Mode 3 (ArgonNX) despite not led's blinking colors matched. I choose Power Off. After i power on while Vol- pressed and still Argon menu showing upp. No Hekate....
" Probably you have payload.bin as memloader "
No sir. Not named as so. For tests i only have payloads numbered : payload1, payload2,and so on...
Dougie... If all else fails, hold down vol+ for 9 seconds. This will reset the chips settings.OK... You are using a trinket.
Sure you are using TRINKET/REBUG?
Are you seeing a blue LED when you press vol+? You should see blue, then white blink, then red, white blink, then green, white blink, finally white and a long long blink
Sure you are using TRINKET/REBUG?
Are you seeing a blue LED when you press vol+? You should see blue, then white blink, then red, white blink, then green, white blink, finally white and a long long blink
I know. ArgonNX is only 1 payload. I left it like that as I figured if people want to choose payload1.bin or payload2.bin or whatever, they would prefer to do it from ArgonNX menu.Oh yes i'm sure.
Now i see the correct blinking order yesterday not. It seemed the Trinket needed a full reset after UF2 flash by my side...But the problem remains i still can't choose/change payload with Vol+. There is not the counter's payload blink. And the console can't not power off. It always reboots onto ArgonNX. No matter which payload manually chosen from ArgonNX menu.
Ah and i forgot to say that i can't boot into Hekate with Vol-/power anymore.
EDIT : Ok. Back to mode 1. Everything works as expected. Counter's payload blink is back. Power Off too. Vol-/power Hekate too.
So the problem is with the Mode 3 : ArgonNX. It's very persistent. On it you can't change payload with Vol+/Long press. Only manually.
I know. ArgonNX is only 1 payload. I left it like that as I figured if people want to choose payload1.bin or payload2.bin or whatever, they would prefer to do it from ArgonNX menu. I can make it autochainload like mode 1 etc if you like.
Hmmm... Needs a autohosoff routine adding to ArgonNX.Ok 0.9.8r2 tested. All is good apart from Power Off with SX OS. It still reboots in ArgonNX.
At the moment, only when vol pressed. You can hex edit it though.ArgonNX works only when i have Vol + Strap connected?
or can i use it when i have only the joy con strap connected?