you're asking me to launch again the emummc? i can try but i tried before 2-3 times and it didn't work so...Yes you can import it, I mean you can also try to see if you copy the file from the 32GB to the 128GB again see if it boot.
you're asking me to launch again the emummc? i can try but i tried before 2-3 times and it didn't work so...Yes you can import it, I mean you can also try to see if you copy the file from the 32GB to the 128GB again see if it boot.
you're asking me to launch again the emummc? i can try but i tried before 2-3 times and it didn't work so...
oh sorry, ok i'll try againI meant copy the files from the 32GB to 128GB again, see if that fix it, perhaps something got corrupted.
if It was hacked it would have been done with a chip. You need to provide the files on the SDCard. Here’s a guide that will tell you how to hack your Mariko with Emunand.Hey all. I just went all modern and bought a Switch. The seller had got it used for their kid and then found out it was banned from going online so was selling it on. This didn't bother me as I don't do online gaming and figured it was banned as it had been modded, which I was planning to do anyway.
The seller knew nothing about, well, consoles in general really and so couldn't tell me anything about what may or may not have been done to it.
No SD card was included.
I hooked up to wi-fi and got Error Code 2124-4508 when trying to connect to ..Online
However the serial is XAJ77002... which according to https://ismyswitchpatched.com means it's definitely patched.
I've muddled my way through Wii and Wii U hacking but despite reading up on the Switch I can't figure what, if anything, has been done to this one and so don't know where to start.
Any help would be much appreciated.
Absolutely does. You will need a jig and a way to inject a payload. Still covered by the same guide but you will chose Erista instead of Mariko. (It’s the very first CFW guide)Thank you. I think I edited my post just as you answered to say "It's been a long day. The serial is actually XAJ70029.. According to that same site it is not patched." I presume this would change your advice?
Thats kind of a crazy hypothesis. Are you able to ping it when not watching YouTube?Is it normal to not be able to ping a nintendo switch using its local IP address when it's very clearly connected to the internet (such as while watching a youtube video)? Or is this a case of the switch not being able to do more than one network-based thing at the same time?
Cool. I was stalling while I was finding/installing YouTube. Confirmed there’s no issue pinging with or without YT running.Ah, I wasn't able to ping it while idle either. But turning Airplane mode on and off unwedged it long enough to start pinging it.
Absolutely. Chips are around $65…just a little more than the cost of a triple A title. Waiting for something that might never come is a waste of time IMO.Weird question , do you guys think hwfly modding a switch is worth in 2023 or should just wait to shell out for rumours
Thanks GarfieldAbsolutely. Chips are around $65…just a little more than the cost of a triple A title. Waiting for something that might never come is a waste of time IMO.
There’s a ton of info and various approaches to this.Hey there,
coder/programmer here, with previous communication experience but no specific Switch nor Bluetooth ones.
I would like to inject extra input(s) on a regular joycon controller data stream.
To do that, I thought I could build a "bridge" (via Raspberry Pi?) connected to the Switch and the Joycon that would normally route traffic from Switch to Joycon and viceversa, except when specifically instructed to alter JC->NSW packet(s) to inject the aforementioned extra inputs.
I have a basic understanding of the matter having read this document set but perhaps someone more experienced than me might point to other resources and/or just confirm whether it's actually doable or not.
Thanks, I'll have a look at the first one especially, since I wouldn't mind having the least amount of BT communication in this project.There’s a ton of info and various approaches to this.
You already found the main RE page that many use.
Here’s an example (in Japanese, use a translation)
https://www.mzyy94.com/blog/2020/03/20/nintendo-switch-pro-controller-usb-gadget/
Here’s another:
https://github.com/mart1nro/joycontrol
Is there a way to have a turbo controller function while pressing the a button as an app in the switch?