Hacking [PICTURES] Snaps of your Wiikey Install

[dopestyle67]

first instal and first soldering experiance really, besides some practice before install. i thought it went pretty smoothly, so far both of my backups work! i couldn't be happier, now i just hope it stays that way!!

 

[dirtycarrot]

This was my first ever mod chip install, pretty happy it all went smooth after looking at some of the disasters ive seen posted on the forums.

Damn that chip looked small when i first saw it though.


nice install, i have mine like that also.

An even better place to put the wiikey is in the bottom right hand corner (where the little clip with the wires is).

The wiikey fits perfectly in that corner, the retention clip for the wires holds it in very snugly - you need to use a tiny amount of force to squeeze it in there, but it's a fantastic spot and no tape of any kind is required.

I wish I had of taken a couple of photos of my install, or the install I did for my friend so that you could see how perfect the fit is.

 

[Kamakazie]

Out of curiosity, why don't you guys just do the fast solder and place the chip right on top of the points?

 

[corbs132]

quick solder has been known for the points to be misaligned with the wiikey. also harder to remove

 

[Louse76]

Pics from my install thread:

I (stupidly) did the chip first.

Then the board.

And since I had a good amount of bare wire showing from tinning the wire overzealously, I "shingled" the hell out of it, over and under each wire - but at least I'll never have a short!

 

[plexo]

ya got enough tape there boyo?

 

[Louse76]

Technically, that's not very much tape at all. It is just an extremely close shot!

 

[plexo]

well i counted 6... thats alot?

hot glue wud do a cleaner job to be honest

 

[leirch]

I'd rather remove electrical tape rather than hot glue in the future >

 

[pcsoon]

Wow! Your install pics are awesome. I'm still awaiting to receive my wiikey (clone?). I have attempted soldering in the past but never with much satisfaction. I always feel like I need a 3rd hand. One to hold the wire, one for the iron and one for the solder. How do you guys do such clean jobs? Is there a device or clamp that helps hold the wire? Do you just build up the point with the solder first and then re-melt it? I plan to practice before doing my install but any tips would be greatly appreciated.

 

[Edster]

Pics from my install thread:

I (stupidly) did the chip first.

Then the board.

And since I had a good amount of bare wire showing from tinning the wire overzealously, I "shingled" the hell out of it, over and under each wire - but at least I'll never have a short!Â

Why do you say it's stupid to do the chip first?

I made 6 wires all equal size. The stripped the ends, tinned them and labelled each 1 - 6. Then I attached the right numbers to the each point on the chip. Secured the chip with tape and attached each wire to the padbs on the PCB. It was pretty simple for me and since I numbered the wires, there was no confusion as to what went where.

 

[juggernaut911]

y r u guys using tape????????
sorry if n00bish... dont know jack bout this

 

[Edster]

y r u guys using tape????????
sorry if n00bish... dont know jack bout this

Tape just to hold the wires and the chip down.

 

[corbs132]

y r u using 1 ltr wrds?
sorry if n00bish... dont know jack bout this

nah jk man i got respect for you. its to prevent shorts and hold everything in place

 

[7llusion]

This is the thirst time I've installed a modchip, and I have to say that I wasn't too difficult but it took time.

I've cut the wires, don't worry.
Illusion

 

[blunty]

This is the thirst time I've installed a modchip, and I have to say that I wasn't too difficult but it took time.
I've cut the wires, don't worry.
Illusion

Looking at those picts, I'm surprised that actually works. Not dissing your skills, but those solder joints
on the chip look dry. Too much solder. I'd be afraid of a short.

 

[airrich]

i forgot to take a pic of the soldering job i did on the drive, but it works.

 

[mallfouf]

Here's mine

2nd time installing

 

[lenselijer]

Nice job mallfouf, this proves once again that a quicksolder install of wiikey is perfectly possible.

 

[Louse76]

Why do you say it's stupid to do the chip first?

I made 6 wires all equal size. The stripped the ends, tinned them and labelled each 1 - 6. Then I attached the right numbers to the each point on the chip. Secured the chip with tape and attached each wire to the padbs on the PCB. It was pretty simple for me and since I numbered the wires, there was no confusion as to what went where.

I made them equal size too. I wanted to mount it in a certain place, and if I had soldered it to the board with extra wire, and then cut it to length, I would have been much better off.