Picofly AIO Thread

[cicci084]

i hope u made a backup off everything just in case something happens

Yes, yes, done!
Nand, Boot, Payload, all as from video.
Thanks again.

 

[Dee87]

Yes, yes, done!
Nand, Boot, Payload, all as from video.
Thanks again.

good keep it in a very safe space . i put it on 3 diffent harddrives/usb sticks just to make sure i never loos it if one drive fails

 

[GrTroller]

Help
I accidentally ripped the dat0 pads off my v2 switch is there another point I can solder to to fix it?

Post automatically merged: Apr 9, 2023

Help
I ripped off the dat0 pads from the board on my v2 switch . Are there any other points on the board to fix this?

 

[Dee87]

Help
I accidentally ripped the dat0 pads off my v2 switch is there another point I can solder to to fix it?

Post automatically merged: Apr 9, 2023

Help
I ripped off the dat0 pads from the board on my v2 switch . Are there any other points on the board to fix this?

Where ?
show us a picture
U might have a issue getting back to runing at all it ur not able to fix it

 

[GrTroller]

Here

Post automatically merged: Apr 9, 2023

.

 

[RexSonic]

How did you manage to do that?

 

[GrTroller]

At first I installed it and it worked . Then when I reassembled it it didn't work and the light was purple . So I kept resoldering the point . In the end this happened

 

[dewolf]

But where I can download the update.bin to update via the toolbox ?

 

[RexSonic]

But where I can download the update.bin to update via the toolbox ?

https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/post-10123184

 

[cicci084]

Help
I accidentally ripped the dat0 pads off my v2 switch is there another point I can solder to to fix it?

Post automatically merged: Apr 9, 2023

Help
I ripped off the dat0 pads from the board on my v2 switch . Are there any other points on the board to fix this?

Take it from the EMMC, the rear side.

See First post.
https://gbatemp.net/attachments/pinout_emmc-jpeg.360378/

You will have to see if they are not interrupted encouraged, in this case you will have to carry out a jumper to restore the correct functioning.

 

[ngoanrazor]

I don't know, Why use 2 wire to control mosfet ?

https://gbatemp.net/attachments/marikodual-mosfet-jpg.363515/

 

[Arakon]

I don't know, Why use 2 wire to control mosfet ?

https://gbatemp.net/attachments/marikodual-mosfet-jpg.363515/

Cause you need to connect both control pins. You can use a single wire and make a bridge instead too, of course.

 

[Dee87]

I don't know, Why use 2 wire to control mosfet ?

https://gbatemp.net/attachments/marikodual-mosfet-jpg.363515/

u dont have to u can use one wire i used 2 its not more u can just bridge them thats good enough .
i just put 2 in the picture so everybody knows/understands it better

Post automatically merged: Apr 9, 2023

Here

Post automatically merged: Apr 9, 2023

.

clean it very good make sure u see copper and see if i can get solder on it or bridge it other wise u will have to use
the point on the emmc u might even have to set a jumper wire to the point if u have issues with the emmc.

u need to use lots of flux and dont use to much heat with ur soldering iron and one u solder the cables put some uv mask on the wire so it gives it a bit strentgh and its a "tiny Bit " harder to rip those cabels of

 

[VashTS]

Yay we got pico support! Would this MOSFET work? I can get it locally.

https://www.microcenter.com/product/614900/nte-electronics-power-mosfet-n-channel

 

[cicci084]

Sorry guys, I don't know how to configure my Switch to automatically boot into EMUmmc.
After following the video to prepare the microsd, as soon as I start the console it starts in hekate, while I would like to start it directly in EMUmmc.
Then, once it's set up correctly, I'd like to know the hekate startup procedure.
Thank you.

EDIT:
i find this option on menu of hekate.
Sorry guys

 

[Arakon]

Yay we got pico support! Would this MOSFET work? I can get it locally.

https://www.microcenter.com/product/614900/nte-electronics-power-mosfet-n-channel

Depends. Do you have a seperate cupboard to store it in?
Jokes aside, that thing is HUGE compared to the recommended MOSFET, and will probably not fit into the switch. It can also cause issues due to different timing etc.

 

[impeeza]

Sorry guys, I don't know how to configure my Switch to automatically boot into EMUmmc.
After following the video to prepare the microsd, as soon as I start the console it starts in hekate, while I would like to start it directly in EMUmmc.
Then, once it's set up correctly, I'd like to know the hekate startup procedure.
Thank you.

EDIT:
i find this option on menu of hekate.
Sorry guys

That was you mistake, video guides always are outdated and sometimes wrong.

you can read the guide:

https://rentry.org/switchHackingIsEasy

for understand the basics configurations.

you need to understand how the file HEKATE_IPL.ini the explanation is on the hekate page:

https://github.com/CTCaer/hekate#bootloader-configuration

when you put the autoboot=2 pointing to a config (on this case the second of the file), and the config have the EmuMMC you always will autoboot on it, by example:

{--- EMUNAND START---}
[CFW (EMUMMC)]
id=EMUNAND
emummcforce=1
fss0=atmosphere/package3
atmosphere=1
logopath=bootloader/EnergyStarBL.bmp
icon=bootloader/res/payload_hue_nobox.bmp
kip1patch=nosigchk
{--- EMUNAND END ---}

Post automatically merged: Apr 9, 2023

note this is my configuration, and as I have custom icon and logo the sentences point to mines.

but emummcforce, fss0 and atmosphere ones are the needed to force emmummc

 

[A-Hacked-Soul]

I got sent the wrong wire. What are the chances this will work?

 

[lightninjay]

I got sent the wrong wire. What are the chances this will work?

Should be doable. Someone else did a full install (minus I think power wires) with 40awg which is just a tad smaller than .1mm

 

[Dee87]

I got sent the wrong wire. What are the chances this will work?

its perfect dont need thicker wire i do all installs with 0.1mm wire
u dont need more