Picofly AIO Thread

[impeeza]

This is a Pikofly AIO Thread/Tutorial.
This information has been pulled from other threads and forums on this site, I haven't done anything except compile it in this one thread.
All credit goes to those who worked on all the relevant information and stuff.

First things First; I not not endorse piracy and those who released the firmware don't either so this is for home-brew use only.

DOING THIS MODIFCATION TO YOUR SWITCH MAY CAUSE PERMANENT DAMGE. I RECOMMEND YOU HAVE THIS DONE BY A PROFESSIONAL INSTALLER

DISCLAIMER! Me nor any of the other temp members who helped make this happen will be held liable to any damage you cause your console in attempting to mod it. Professional installation is recommended for this mod.

Just because a mod is cheap doesn't mean it's easy. - Trust me I learnt the hard way - Adran 2023

General InformationInstallation overviewImagesCredits

1. 
   

   RequirementsHintsLED IndicatorsFAQ's

   1. 
      
      • RP2040-Zero
      • SMD 8050 47 to 50 ohm Resistors
      • Mosfet (IRFHS8342 MOSFET) or cpu flex cable (lite flex for lites, v2 flex for v2 mariko etc etc)
      • switch (duh)
      • Wire
      • RP2040 Firmware (direct Link)
   2. 
      
      
   3. 
      
      
   4. 
      
      
   
   
2. 
   
   
3. 
   

   Mosfet ImagesSolder Points

   1. 
      
      
   2. 
      
      
      
      
      
      
   
   
4. 
   
   

P.S More formatting and information to come

I really love to see the McFly becoming a real thing

 

[Dr_Dankenstein]

wait so I have a v2 switch, I bought some wire and a pico board, also grabbed a v2 flex cable
by the diagrams i would assume my points for a v2 console are just on the emmc? if thats the case do i need this ribon cable when it comes? or do i just follow the diagram here after flashing and solder to the emmc and im good to go?

videos I found seem to show insalls on switch lites mostly?

 

[Dee87]

wait so I have a v2 switch, I bought some wire and a pico board, also grabbed a v2 flex cable
by the diagrams i would assume my points for a v2 console are just on the emmc? if thats the case do i need this ribon cable when it comes? or do i just follow the diagram here after flashing and solder to the emmc and im good to go?

videos I found seem to show insalls on switch lites mostly?

v2 flex cable comes on the apu , then u need to solder it to emmc +3v and gnd flash the chip solder everthing to the chip then ur ready to go

 

[Dr_Dankenstein]

ah gotcha thanks
I think i did manage to find an install image too if it helps anyone

 

[kylum]

could u link me some good ones for my Oled ?

not really that familiar with reballing the emmc

Best bet is from Ali mate. But if you can wait im sure they will start to show up in other places as well.

 

[Dee87]

ah gotcha thanks
I think i did manage to find an install image too if it helps anyone

u can also solder the emmc wires to the board like i did but only do that if ur comfortable with soldering at the emmcu connector :-P

i also solderder a flex connector to the usb port from the rp2040
Klick me 2

 

[Battlegames]

Hello, im trying with a V2 switch but in atmosphere console doesnt wake up after press power button or go to sleep mode, what can i do?

thanks

 

[Donnie-Burger]

Hello, im trying with a V2 switch but in atmosphere console doesnt wake up after press power button or go to sleep mode, what can i do?

thanks

Do me a favor and power off and back on then try again. This happened to me once I believe, It's early and there's bugs.

 

[Battlegames]

Do me a favor and power off and back on then try again. This happened to me once I believe, It's early and there's bugs.

always happen, other thing is i cant go stock from hekate (black screen)

Post automatically merged: Mar 25, 2023

always happen, other thing is i cant go stock from hekate (black screen)

i dont remove 3.3v regulator, could be that?

 

[Donnie-Burger]

always happen, other thing is i cant go stock from hekate (black screen)

Post automatically merged: Mar 25, 2023

i dont remove 3.3v regulator, could be that?

If you updated OFW after pico this happens with OFW boot
If you replaced hwfly with pico this happens with OFW

Did you do any of these>? I'm not sure about sleep and 3v3 as I'm waiting for 2.6fw or further news before I remove usbc, port and 3v3 regulator.

 

[Battlegames]

If you updated OFW after pico this happens with OFW boot
If you replaced hwfly with pico this happens with OFW

Did you do any of these>? I'm not sure about sleep and 3v3 as I'm waiting for 2.6fw or further news before I remove usbc, port and 3v3 regulator.

i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

 

[meha]

Hello guys, I'm planning to install on mariko. Do I need to remove the buttons/port or does it fit inside switch? Thanks

 

[Donnie-Burger]

i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

Did you use 47 Ohm resistors?

 

[Battlegames]

Did you use 47 Ohm resistors?

yes , on cmd, clk and dat0

 

[Adran_Marit]

i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

yes always use the original downloads.

if you updated your firmware recently you need to boot full stock.

 

[Dee87]

i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

Its not hats I have hats also running

 

[Adran_Marit]

Its not hats I have hats also running

Just cause it works foe you doesn't mean it won't work for someone else

 

[minik1971]

BUENOS DIAS COMPAÑEROS ME PODRIAN DAR LOS DIAGRAMAS PARA LA PICOFLY PARA V1 GRACIAS

 

[brecht6]

.
.
.

Changelog: Added Erista v1? diagram

P.S More formatting and information to come

It's a v2

 

[Adran_Marit]

It's a v2

V1 and v2. Got clarification from my source. Oled diagrams are coming at some point sooon