Can you add pic for erorr.!!!Detailed istall photos may help
Can you add pic for erorr.!!!Detailed istall photos may help
Same thing is also happening to me but I don't have a nand backup to restore. But I'm thinking about creating a new rebiud nand using Sthetix Guide.maybe the nand is dead
error is in ofw, nintendo logo, then black screenCan you add pic for erorr.!!!
Patched console?error is in ofw, nintendo logo, then black screen
Try to remove sdcard, is it still the same?error is in ofw, nintendo logo, then black screen
only the nintendo logo, the joy con does not appearTry to remove sdcard, is it still the same?
Try to check again, maybe theres cable short or something.
When the nintendo logo shows up especially when the joycon logo shows, its the time when the voltage change. So might be something disturb the voltage line.
Yes i know, right after the nintendo, the joy con appear.only the nintendo logo, the joy con does not appear
i dont know what is warmboot, i search itYes i know, right after the nintendo, the joy con appear.
So it might be when the voltage try to go under, it failed.
It just one probability, the other probability is the data corrupted.
I think the most safe one is try to update the firmware.
Still remember the first time the firmware security unlocked, it have that bug.
I couldn't run the ofw, by vol+ vol- also couldnt from the hekate bottom right menu.
Only could run the ofw from the Warmboot Fix option in Launch menu inside hekate.
If you follow the tutorial on rentryi dont know what is warmboot, i search it
I temporarily installed another chip with the new firmware, it gives me this error, could it be an RTS error?First note for oled is do it very carefully, especially in clk and dat0.
I think its better to upgrade the firmware to 2.73 first. Be safe than sorry.
COUGHI don't know that, apart from reading the rating and general info available, but after some years of trying different ones you eventually end up with a brand you like.
But if you open up a 1yr old piece of equipment which has never been opened before and you see thermal paste hard as stone which crumbles like sand when you try to clean it then you know it was a sh*tty quality to begin with.
Yes it is.I temporarily installed another chip with the new firmware, it gives me this error, could it be an RTS error?
Okay thanks I will see if that helps. Although it has never failed to glitch it just takes 20+ seconds sometimes. Its very random. Sometimes it will take 2 seconds, sometimes around 10 seconds, and occasionally 20+ seconds.
it's strange, the cable has continuity from the RST to the chip, I'm going to change the cableYes it is.
** RST is not connected
Basically the code detecting from the voltage.
View attachment 374021
Detect whether the RST is 1.6 - 2.0 Volt
Nice. Thank you. Out of curiosity, What's your preferred MOSFET installation method? Caps or no caps?This has been previously discussed. As abal1000x said, caps smooth the signal. Although they seem to not matter in most of the cases it was suggested that if you play a game/app that has a high resource demand the APU might experience unexpected behavior due to these caps not being present.
I don't remember seeing any post where this happened, but then again, if it is an unexpected behavior that we are expecting how can we know what it was
show a close up shot where you solder cpu flex pin3,4 to rp2040-zero. My eye tells me you solder rst on pin25 and cpu on pin26I temporarily installed another chip with the new firmware, it gives me this error, could it be an RTS error?
The vast majority of us prefer to leave the caps on. Removing the caps was moreso earlier in the experimentation process when we were deciding the most efficient positioning of MOSFET's.Nice. Thank you. Out of curiosity, What's your preferred MOSFET installation method? Caps or no caps?
I agree. 2.7+ Diagnostics are a life savior. I did a V2 and was working fine, then it slipped out of my hand and was hit to the ground. Ever since it's been booting OFW. I checked the lights and it was ==*. I knew it was the G point wires because it's the most difficult for me to solder and was not happy with it. I resoldered it and now it's working fine.Yes, that is what i'm thinking. But I would still go with 2.73 since it has a way more advanced diagnistics. Or you could try 2.67 and then 2.73, up to you.
Thank you for the explanation.I don't know that, apart from reading the rating and general info available, but after some years of trying different ones you eventually end up with a brand you like.
But if you open up a 1yr old piece of equipment which has never been opened before and you see thermal paste hard as stone which crumbles like sand when you try to clean it then you know it was a sh*tty quality to begin with.
It seems you're right I see the rst goes to the flex cable.show a close up shot where you solder cpu flex pin3,4 to rp2040-zero. My eye tells me you solder rst on pin25 and cpu on pin26