Hacking Hardware Picofly - a HWFLY switch modchip

[abal1000x]

.

 

[nico77]

how to measure the point Dat0 CMD CLK with multimeter ?
i mean, once they are soldered to cables.
how to make sure they are properly soldered to cables ?

 

[abal1000x]

.

 

[SQc04]

How much did it come out In production

Not very good estimate, according to the exchange rate approximate price of 1.5$

 

[impeeza]

LOL what?

looks like Waveshare made a new "dev board" with detachable USB, resistors (47 ohm?) on pins 27, 28, 29, and "custom jumpers" on pins 24, 25.
https://www.waveshare.net/shop/RP2040-Tiny-Kit.htm

Waveshare, Share our wave?

 

[nico77]

i assume purple led is about emmc read failed. If it is true, then need to check the clk and cmd line. Usually bad solder, but if the solder is good, then reduce the noise by adding resistance value, or change the wire with a better one (copper not aluminium), or shorten the length.

Post automatically merged: May 3, 2023

Usually just use Continuity test between the resistor and the point on the motherboard.
Resistor rarely broken, but to make sure do check resistance.
I don't remove the resistor, and its read 47 ohm all the three.

so adding one more 47+47 to the CMD and CLK ?
is it ok to add them to all three point D0 CMD CLK ??

yeah my cable still to long( last time i only test em), i need to reduce the lenght.

 

[QuiTim]

I have, but I'm still sorting through the information
View attachment 368666
View attachment 368669

Great work. Can I ask, are you using P mosfets on these?
Is there any reason/benefit in doing so?
Thanks

 

[789-Benny]

Instead of MOSFETS can use the flexi tape v2? That has mosfets on it already?

For OLED TOTK Model.

 

[Modi]

Instead of MOSFETS can use the flexi tape v2? That has mosfets on it already?

For OLED TOTK Model.

Yes you can

 

[Alpuerto213]

Will the hwfly flex cable lite + rp2040 zero works on switch v2?

 

[Modi]

Will the hwfly flex cable lite + rp2040 zero works on switch v2?

Yes it works fine

 

[Browbon]

@QuiTim sorry for mention you. May i ask you some questions? what difference between using single mosfet and dual mosfets? i'm trying to apply single mosfet method.

 

[789-Benny]

View attachment 368616
View attachment 368651
View attachment 368617
PICOFLY ИX module (verified)
https://github.com/SQc04/PICOFLY-X
Use easyeda PRO
https://easyeda.com/
The CPU cable will be released later
The resistor uses 0402 and is not recommended for novice welding
The circuit board is 0.8mm thick

V0.8.1+ supports jumpers, V1 V2 LITE OLED universal

Do we have a release for the cable?

 

[pedale]

Best regardsl

Just tried to boot EmuMMC CFW and it says "A fatal error occured when running Fusée. Package1 seems corrupt!"

Also Warmboot says "Unknown pkg1 version. HOS version not supported"

What can I do now?

I have the same problem

 

[jv_233]

Best regardsl

I have the same problem

Add another resistor to the dat0

 

[789-Benny]

Should this work for mosfets on oled?

https://uk.rs-online.com/web/p/hook-up-wire/2094811

seems correct as thickness under 0.5mm
Or can anyone show a better product for uk?

 

[A-Hacked-Soul]

My workshop is covered in dropped or launched resisters.

 

[QuiTim]

@QuiTim sorry for mention you. May i ask you some questions? what difference between using single mosfet and dual mosfets? i'm trying to apply single mosfet method.

No problem.
To be honest I don't know. It seems that sometimes (for reasons unknown to me) one mosfet does not work.
I've only done 2 switches (both V2) with pico, and both of them worked with one mosfet (1st one with irf8714 the other one with irfsh8342).
Use good wire, keep the length of the wire to minimum and solder good joints and I'm 99% sure it will work with one.

 

[Modi]

No problem.
To be honest I don't know. It seems that sometimes (for reasons unknown to me) one mosfet does not work.
I've only done 2 switches (both V2) with pico, and both of them worked with one mosfet (1st one with irf8714 the other one with irfah8342).
Use good wire, keep the length of the wire to minimum and solder good joints and I'm 99% sure it will work with one.

Im use to Mariko (V2) flex from V1 Erista with one mosfet made over 20+

 

[QuiTim]

Im use to Mariko (V2) flex from V1 Erista with one mosfet made over 20+

Well yes, i guess as long as the soldering is solid and the wires support the load, one mosfet is ok.
You have 20+ witnesses that support this