I see no flux *angry noises*...getting ready for tomorrow... wish me luck
View attachment 364918
... Thanks for all the great people involved in making this Mod possible!
I see no flux *angry noises*...getting ready for tomorrow... wish me luck
View attachment 364918
... Thanks for all the great people involved in making this Mod possible!
IRFHS8342 MOSFET is used...Sure you can solder all pads separately. But as I see, you use a different, much larger mosfet, I'm pretty sure single one is enough, no need to setup dual
This wiring is very smart but difficult.why dont u take the images out of the aio thread
...oops! forgot to include it in the picI see no flux *angry noises*
Thx for the quick reply, mate!I mean show photos of the board, since it's hard to see where exactly those wires are soldered to. My diagrams assume soldering directly to the eMMC board, or, at least, to its header, I am unaware of other points. Just wanted to check
Post automatically merged:
In the same message you just quoted
https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/page-78#post-10090767Thx for the quick reply, mate!
I mean where are all the firmwares being posted? Like a repository?
Also, what does sufix "_I" mean?
your wire looks too thin, remember, it should handle around 20-40A in pulseGuys, I'm having cyan led and starting directly original system? ideas? I already soldered 2 mosfets, it only worked with the flat v2, but I wanted to know the reason for not working with the mosfet in this lite, I already made other devices that worked ok
why not, it's the same cable, should work same wayDoes anyone know if Sx Lite flat CPU cable would work with PicoFly? I have that one installed and I would like to replace SX with PicoFly. My SX is really unstable.
no repository, I delete older firmwares and add the latest one in my post. however there is an unofficial one on github.Thx for the quick reply, mate!
I mean where are all the firmwares being posted? Like a repository?
Also, what does sufix "_I" mean?
Does anyone know if Sx Lite flat CPU cable would work with PicoFly? I have that one installed and I would like to replace SX with PicoFly. My SX is really unstable.
I've done other installations with this wire, it worked without problems, but I'll try another one next timeseu fio parece muito fino, lembre-se, ele deve lidar com cerca de 20-40A em pulso
encontre fio de 0,2 mm de diâmetro, solde-o adequadamente ao mosfet
Post automatically merged:
por que não, é o mesmo cabo, deve funcionar da mesma maneira
Post automatically merged:
sem repositório, excluo firmwares mais antigos e adiciono o mais recente no meu post. no entanto, há um não oficial no github.
Eu descrevi a diferença alguns posts antes, _l significa tempo limite mais longo
nois there any donation link for you?
From the photo it also looks like cold joint for the S wireI've done other installations with this wire, it worked without problems, but I'll try another one next time
Yeah, I solved it the best way (I put the flex of v2 in that lite) but now I got a v2 and soldered the mosfet directly to the capacitors, even though it was a v2 nand toshiba it worked super well with fw 2.65. Thanks for all my friend!no
Post automatically merged:
From the photo it also looks like cold joint for the S wire
Check "Important Posts" tab at the top of the page for a link called "Firmwares"Where can I download the latest firmware
Best of luck, mate!
Please see my earlier post about getting the LATEST firmware. The tab at the top should redirect you to a post by Rehius with the 2.65 firmware.I encountered an issue while using the 2.5 firmware. The rp2040 lights up in blue when turned on, but after pressing the reset button of rp2042 after turning on, the rp2040 lights up in blue for 5 to 15 seconds before entering the atmospheric guidance interface.
why difficult ?IRFHS8342 MOSFET is used...
Post automatically merged:
This wiring is very smart but difficult.