just to know, rp2040 one is working with all switch models? cause i bought 18. thanks
why you hoarding?just to know, rp2040 one is working with all switch models? cause i bought 18. thanks
It's clearly stated that this was developed for the RP2040 Zero.just to know, rp2040 one is working with all switch models? cause i bought 18. thanks
I also want to know if the 2040 one works, because I saw a video where it worked and I thought it was safe, but lately I have seen that several users have tried to install it with problemsgood afternoon fellow workers, a question the rp2040-one is used to be able to install in the console I have this doubt since the zero has 2 memory and this one has 4 memory it will be that it is not compatible
It is a 4C10N and it works like a charm. I also added a 2.4K resistor between the gate and ground to immediately discharge the gate when not in use. It usually takes one second to successfully glitch the console. It rarely take up to ten seconds. I also got the payload working now. I was using the wrong method.oot.. what type mosfet is that , looks big
good afternoon fellow workers, a question the rp2040-one is used to be able to install in the console I have this doubt since the zero has 2 memory and this one has 4 memory it will be that it is not compatible
Some got it working, others havent. So far the issue I have is red flash once and won't boot with cmd connected. Others have had the red flash thing tooI also want to know if the 2040 one works, because I saw a video where it worked and I thought it was safe, but lately I have seen that several users have tried to install it with problems
View attachment 361515
I have tried the PGA2040 and no success. I added an ARGB LED to see the status and ist just flashes red once and then does nothing. I don't know what the reason could be. It is the same controller and the only real difference is the SPI flash which is a different model and much larger. I then switched to the Waveshare one and it worked.Some got it working, others havent. So far the issue I have is red flash once and won't boot with cmd connected. Others have had the red flash thing too
Maybe some installed it incorrectlySome got it working, others havent. So far the issue I have is red flash once and won't boot with cmd connected. Others have had the red flash thing too
I used the same diagram for the rp2040-one as the zero.... I assume based on the similar design that its the same. Although I didnt hook up CPU at all, I would expect it to blink cyan like the guide saysMaybe some installed it incorrectly
current firmware encryption assumes you have rp2040-B2 with Flash ID starting as E6-6xI used the same diagram for the rp2040-one as the zero.... I assume based on the similar design that its the same. Although I didnt hook up CPU at all, I would expect it to blink cyan like the guide says
current firmware encryption assumes you have rp2040-B2 with Flash ID starting as E6-6x
it could be your one has -B1, or -B0 chip, or the flash ID is different
will be also disabled in v2.6...
Would also explain why my regular Pico didn't work. Is there a quick way to check flash id?current firmware encryption assumes you have rp2040-B2 with Flash ID starting as E6-6x
it could be your one has -B1, or -B0 chip, or the flash ID is different
will be also disabled in v2.6...
you need at least 256 KB flashThat would explain that, the 4MB vs 2MB doesn't matter?
Page 10 of this threadIs there a quick way to check flash id?
My points are correct and when I switched out for hwfly, it boot up fine.Maybe some installed it incorrectly
I just got the zero in and it act differently after you install the firmware. I think it’s our one chips or it’s the bootloader that might be giving us the problem.Some got it working, others havent. So far the issue I have is red flash once and won't boot with cmd connected. Others have had the red flash thing too
looks like stubborn Toshiba eMMC, still waiting for samples to analyzeHmmm, fixed the CPU cyan error.
Now on blue it just pulses blue until I switch it off?
Using the V1 flex on Erista.
Thanks,
Ant
looks like stubborn Toshiba eMMC, still waiting for samples to analyze
its worth a shotHmmm, fixed the CPU cyan error.
Now on blue it just pulses blue until I switch it off?
Using the V1 flex on Erista.
Thanks,
Ant