Nah the first install i did I had two mosfets outside of the cpu shield, the rest all glued inside the shieldJust to be clear, did you put the mosfet outside cpu shield on those 8 oleds?
Nah the first install i did I had two mosfets outside of the cpu shield, the rest all glued inside the shieldJust to be clear, did you put the mosfet outside cpu shield on those 8 oleds?
When you install the mosfet outside the apu shield, and the glitch worked, did you use 30awg, around 10 cm length?Nah the first install i did I had two mosfets outside of the cpu shield, the rest all glued inside the shield
(Sorry lot of ask, i might replicate this. Its wonderful if i could do it. I will change my default mod as mosfet outside from the apu.)Nah the first install i did I had two mosfets outside of the cpu shield, the rest all glued inside the shield
I've used the CPU ground(the small square in the right hand corner of the cpu), but it it a hard connection to make, I just use the chasis nowWhen you install the mosfet outside the apu shield, and the glitch worked, did you use 30awg, around 10 cm length?
Post automatically merged:
(Sorry lot of ask, i might replicate this. Its wonderful if i could do it. I will change my default mod as mosfet outside from the apu.)
The gnd of the mosfet, you take it from the cap, the chasis or somewhere else?
lol yeah, thats squared is like magic. Difficult to solder.I've used the CPU ground(the small square in the right hand corner of the cpu), but it it a hard connection to make, I just use the chasis now
I have updated to firmware 2.74 ,Picofly keeps waking up my device ,so I can't completely shut down. I'm not sure if this is a common situation. My device is a Switch OLED.2.74 w/o i2c
Thats look beautiful.Looks clean enough, let see how short can i make this wire to be.
Once among us cleaned the flex using ipa.another attempt on 2nd OLED, damn my screen wont turn on but it got sounds (this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? , all connector seems fine
The device will wake if you plug a usb cable in fyiI have updated to firmware 2.74 ,Picofly keeps waking up my device ,so I can't completely shut down. I'm not sure if this is a common situation. My device is a Switch OLED.
Check the pins inside the female flex connectoranother attempt on 2nd OLED, damn my screen wont turn on but it got sounds (this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? , all connector seems fine
The device will wake if you plug a usb cable in fyi
Post automatically merged:
Check the pins inside the female flex connector
No, I didn’t insert a USB. It’s just battery-powered. After I turn off the power, the chip will work and wake up the device.The device will wake if you plug a usb cable in fyi
Post automatically merged:
Check the pins inside the female flex connector
The chip does not wake the console. This is a well known RTC auto power on after shutdown used by N system. Every Switch console automatically turns on after poweroff from the Horizon OS, even the unmodded ones.No, I didn’t insert a USB. It’s just battery-powered. After I turn off the power, the chip will work and wake up the device.
A question: Using two mosfets, is it necessary to bridge the ground of both to the point of the apu, or can I separate them and connect them independently to the same point?
You can seperate them there is no harm, but you have to make sure good secure connection. Do not make cables too long or different sizes. Make it as short as possible and same size.
Sent from my iPhone using Tapatalk
That squared is very difficult to solder. I am afraid you breaking something while doing it. Better just use chassis, simple and easy.So, using the yellow way in the picture is ok?
I tried to soldering using the green example but I can't do it very well.
So, using the yellow way in the picture is ok?
I tried to soldering using the green example but I can't do it very well.
Solder like purple lines. Yellow is more difficultSo, using the yellow way in the picture is ok?
I tried to soldering using the green example but I can't do it very well.
I personally don’t recommend using APU as ground point. Use APU shield instead.
Sent from my iPhone using Tapatalk
Ok, I`ll use shield as ground point. Thanks.That squared is very difficult to solder. I am afraid you breaking something while doing it. Better just use chassis, simple and easy.
I can´t see any purple lines on the image I`ve attached. You mean same as Bad and Abal? Using APU shield as ground point?Solder like purple lines. Yellow is more difficult
Ok, I`ll use shield as ground point. Thanks.
I can´t see any purple lines on the image I`ve attached. You mean same as Bad and Abal? Using APU shield as ground point?
BTW, Can I use APU shield too soldering the GND point of RP2040? In the past I modded one Lite and the ground point at the capacitor scares me a little bit hahaha