Picofly AIO Thread

[Eierfeile]

so i managed to reactivate a V1 to test the emmc and turns out the keys are fu**ed up.
Keyblob 0-5 and CAL0 error on SSL and ETICKET and somewhat with biskey 0.
anyone have a idea about that?

 

[ngoanrazor]

Please help me, I make broken CLK point and now, sw lite can not boot, how to fix this problem?

 

[lightninjay]

Please help me, I make broken CLK point and now, sw lite can not boot, how to fix this problem?

 

[ngoanrazor]

I can not see this point on pcb, I use wire 0.2mm and it too hard

 

[Eierfeile]

Please help me, I make broken CLK point and now, sw lite can not boot, how to fix this problem?

the CLK point on the Switch Lite goes through 2 layers on the PCB.
you can place 0.25 or 0.3mm solderballs on the ripped pads and reflow with hot air. (small nozzle,relatively high temp and lowest airflow) and then hope for the best that the balls stick to the vias. if yes then you can make a jumper wire.

hope this helps

 

[naldo29]

quick question, the pinouts are the exact same for the v1erista as for the v2mariko correct?

 

[Dee87]

quick question, the pinouts are the exact same for the v1erista as for the v2mariko correct?

yes

 

[Raugo]

I tried a lot of things and still have the problem wht the boot0/boot1 and slow mode of the emmc. I maked a emummc and can launch HOS from it. Is dangerous to leave it at this for the moment? I'm really tired and want to rest.

 

[FreeLander]

the CLK point on the Switch Lite goes through 2 layers on the PCB.
you can place 0.25 or 0.3mm solderballs on the ripped pads and reflow with hot air. (small nozzle,relatively high temp and lowest airflow) and then hope for the best that the balls stick to the vias. if yes then you can make a jumper wire.

hope this helps

Pretty cool. Will this technique work on OLED's point D? If it gets scratched too deep?

 

[Dee87]

I tried a lot of things and still have the problem wht the boot0/boot1 and slow mode of the emmc. I maked a emummc and can launch HOS from it. Is dangerous to leave it at this for the moment? I'm really tired and want to rest.

Did u add additional resistor to D0 and CMD I think it was?

 

[abal1000x]

.

 

[demonfish]

This is for micro soldering. You need minimum some lenses. Better option a microscope lenses. And the best of all use a microscope hdmi. Its almost impossible doing it without the right tool, except you are a very skilled and experienced veteran electronic technician.

We are going to be seeing a large influx of faulty switch console on eBay. I see already many peeps f@@king there switch up with this mod.

 

[nico77]

This is for micro soldering. You need minimum some lenses. Better option a microscope lenses. And the best of all use a microscope hdmi. Its almost impossible doing it without the right tool, except you are a very skilled and experienced veteran electronic technician.

in other universe :
me goin to smartphone service center...

me: help me solder this n this n this, ill pay you...

 

[Eierfeile]

Anyone experienced that after the installation of the picofly the complete battery info is gone?
i already replaced the fuel gauge but the problem is still there

 

[spaceraccoon]

in other universe :
me goin to smartphone service center...

me: help me solder this n this n this, ill pay you...

i would laugh but that could easily be me

 

[malgamer]

Anyone experienced that after the installation of the picofly the complete battery info is gone?
i already replaced the fuel gauge but the problem is still there

hi still able to charge your switch console?

 

[WalangAlam]

where do you put the picofly in lite? on top of the metal cage? can you add also images of recommended placement of picoply and wire management...

 

[lightninjay]

Here are the two most viable options, I personally went with the second option.

 

[WalangAlam]

i am using the second option but it seems it wont fit with the metal cover. i will try again tonight...

 

[lightninjay]

i am using the second option but it seems it wont fit with the metal cover. i will try again tonight...

It certainly fit in mine, even with the kapton tape. However, I also turn my 0805 resistors to the inside of my board.