Hacking Hardware Picofly - a HWFLY switch modchip

[malgamer]

hey a question here i have hack a few consoles now using picofly , all the samsung emcc boot in 1 sec , the tochibas are like ramdom time , its this normal in tochiba

Have you tested it yourself on TOSHIBA? and DAT0 and CLK keep 47 ohm?

my dat0 240 ohm , clk 50 ohm, cmd 50 ohm with this setup for toshiba emmc also have slow glitching issue

 

[abal1000x]

.

 

[Dust2dust]

If we're gonna be picky, it should be pronounced Heck-a-Tea

I checked on the origin before making the post, both pronunciations are technically correct, but the modern Anglicism of the word is as I mentioned, HECK-eight. I normally pronounce it poshly, Heh-kah-tay.

According to this, hippy dave is the winner. It's been a while, but the last time I watched the movie Jason and the Argonauts (on Netflix), there was a woman who talked about this goddess and pronounced it as lightninjay mentioned, Heh-kah-tay. It's really hard to tell how to say it.

 

[jkyoho]

my dat0 240 ohm , clk 50 ohm, cmd 50 ohm with this setup for toshiba emmc also have slow glitching issue

try swap 240ohm with the cmd 50ohm ?

 

[malgamer]

try swap 240ohm with the cmd 50ohm ?

ok i will try it later and share the result

 

[QuiTim]

Seeing Hekake just makes me think of bukkake, which I would prefer not to think about. Just a friendly little PSA

 

[Danook28]

Is microscope boom rf4 use one lence if look and 2 lence i see only from right lence left lence is darkness????!!!

 

[SQc04]

The scenario has been successfully tested

 

[cicci084]

guys, we've been missing for a while.
I had doubts about the stability of fw 2.74, that's why I was installing 2.67.
Now I see that the problem has been recognized, and 2.73 is recommended.
Can I safely update all the consoles with which I installed with 2.67?
Or do I stay like this?

 

[cgtchy0412]

View attachment 379488View attachment 379489View attachment 379490View attachment 379491
The scenario has been successfully tested

For 3.3v it is because to risky with flex or you double it or its just you still need wires? even with commercial flex.

 

[SQc04]

For 3.3v it is because to risky with flex or you double it or its just you still need wires? even with commercial flex.

Yes, the 3v3 pads are too far away

 

[abal1000x]

.

 

[cgtchy0412]

guys, we've been missing for a while.
I had doubts about the stability of fw 2.74, that's why I was installing 2.67.
Now I see that the problem has been recognized, and 2.73 is recommended.
Can I safely update all the consoles with which I installed with 2.67?
Or do I stay like this?

I say, if you still have hands on then yes you need to downgrade.
Although i personally waiting for hipotetical 2.75 with maybe 250mhz oc and disabled SDA/SCL feature. of course until i can compile the source code myself.

Post automatically merged: Jun 23, 2023

Yes, the 3v3 pads are too far away

Any apparent changes in glitch time? or general stability if we compare with original pico instalation?

 

[jmmc]

v2 need 100ohm.

Try to backup the raw emmc, usually theres show problem.
Benchmark the emmc might not triggered it.

Hmmm I don’t think it’s always mandatory. I did a few days ago a v2 with a rp2040-tiny and I didn’t have to add any extra resistor (just the ones which has the board included)

 

[abal1000x]

.

 

[KingMo5h]

For the people who are searching for good oled dat0 pcbs, I ordered here: https://vi.aliexpress.com/item/1005...il_item.3.1a50f19crRcduK&gatewayAdapt=glo2vnm
They sell 2 different ones, the bad Oat0 ones and Dat0 V6. I ordered the V6, i will report back when i got them but takes 12 days at least..

 

[QuiTim]

the purple happends when after a 10 power off and on train to get to hekake , but only ofw , the issue go away just by putting the battery of and on . iam isntalling BUNCH OF THINGS TO THE EMCC 40mbs no issues , just to see if i can see a issue

Post automatically merged: Jun 23, 2023

any magnetic fusse out there that i can buy and sother to the reset on the pico ?

you could use these to reset the pico if you don't find a fix for the problem
https://vi.aliexpress.com/item/1005003372450508.html
maybe use the "normaly open" model and solder it to reset button pads on pico

 

[Danook28]

if you want to buy microscope. maybe you could look on hdmi microscope.

I buy rf4 boom microscope with 2k camera rf4...i think that only normal can see from one lence and the other one is darkness... Normal!!!!!

 

[abal1000x]

.

 

[beeboy]

If we're gonna be picky, it should be pronounced Heck-a-Tea

it's pronounced gif


hehe