Hacking Hardware Picofly - a HWFLY switch modchip

[Modi]

atmosphere release new update v1.5.3 can run 16.0.3 now

Already make picofly Erista on 16.0.3. Have problem dont Wake up from sleep Mode but fix it with new update.

 

[AspenFTW]

Hi anyone can help me on why hekate doesnt boot now on OFW 16.0.3? It's always booting to OFW even No SD is not showing if I remove the sd card. My picofly version is 2.67

 

[axlcat]

Hi anyone can help me on why hekate doesnt boot now on OFW 16.0.3? It's always booting to OFW even No SD is not showing if I remove the sd card. My picofly version is 2.67

Did you update hekate and atmos?

 

[abal1000x]

.

 

[s4n0suk3]

Hi again everyone I still having problems with my install, blue them cyan, im using 0.1mm emeled wire, I need anoter size or just with 0.1 it can work?

 

[JoTiK]

Hi again everyone I still having problems with my install, blue them cyan, im using 0.1mm emeled wire, I need anoter size or just with 0.1 it can work?

I used awg 38 too and it works well

 

[Kiuxn]

Some said it does not work.

https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/post-10152378

My friend found the problem. 2040-tiny uses 470 ohm instead of 47ohm

Post automatically merged: May 10, 2023

My friend found the problem. 2040-tiny uses 470 ohm instead of 47ohm

Replace 470 ohm and it will be successful.

 

[Modi]

Hi anyone can help me on why hekate doesnt boot now on OFW 16.0.3? It's always booting to OFW even No SD is not showing if I remove the sd card. My picofly version is 2.67

Just update all works fine . test it today

 

[abal1000x]

.

 

[jkyoho]

My friend found the problem. 2040-tiny uses 470 ohm instead of 47ohm

Post automatically merged: May 10, 2023

Replace 470 ohm and it will be successful.

I guess that's why it's out of stock now

 

[Modi]

Even waveshare confused with the 470 Ohm and 47 ohm

SMD 470 equal to 47 ohm not 470 ohm .
I confuse too at the beginning, always read carefully.

Now i know why my order still waitng to ship from china ...

 

[789-Benny]

what i like about tiny.
no need to cut/trim anymore hehehe

zero need to remove the usb-c port , so we can fit board for lite.
you cant install the metal shield with those usb-c port still attached. lite

Cut the shield and stick it where the RAM is, doesn't affect the temps (another user few posts suggested this back a few pages)

Fits without issue, just use some kafton tape over the ram and you can use hot glue to keep the board from moving on the metal plate that runs between the ram and gpu.

 

[1337_Ninja]

My friend found the problem. 2040-tiny uses 470 ohm instead of 47ohm

Post automatically merged: May 10, 2023

Replace 470 ohm and it will be successful.

Is there anyway you can give us proof of this? Or can someone else confirm?

 

[Chonay]

Has anyone already found an alternative to the mosfets that are very slow to get?

 

[LogicalMadness]

Hi anyone can help me on why hekate doesnt boot now on OFW 16.0.3? It's always booting to OFW even No SD is not showing if I remove the sd card. My picofly version is 2.67

Take it apart and check cpu-flex\MOSFET(s), I smell cyan...

 

[ecko4711]

Quick question guys. My Pico zero has already detached usb c and buttons. I was on fw 2.5 i think. I think i should update, when there is a new firmware, like 2.67 right now, for my pico zero, but how can i do that? resolder usb c?

 

[Kiuxn]

Is there anyway you can give us proof of this? Or can someone else confirm?

I've got the pr2040-tiny. It's really 470 ohm. Just replace it.

 

[QuiTim]

I've got the pr2040-tiny. It's really 470 ohm. Just replace it.

What size are they?

 

[deejay87]

Hi, does the 2.67 can work with official boot with hekate ?
reboot > OFW
Cause i stay on screen off, stock (sysnand) work, Thanks

 

[tortosa_juaskas]

So which are they, 47 ohms or 470 ohms?

I just installed PicoFly and it gives me the same result, the led lights up but nothing on the screen and it makes a little noise.