[Guide] How To Hack Your 360

Discussion in 'Xbox 360 - Hacking & Homebrew' started by DinohScene, Sep 12, 2012.

  1. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    My bad, its RGH 1.2. Probably should have mentioned that ...

    Either the Matrix or Coolrunner will work, but the Matrix is cheaper.
     
    awdrifter likes this.
  2. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Cool, thanks for the info.
     
  3. Tumoche

    Tumoche GBAtemp Regular

    Member
    5
    Apr 30, 2017
    Spain
    brickmii82 likes this.
  4. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Damaged the board beyond repair?
    But yes, that one can be used.
     
    brickmii82 likes this.
  5. Tumoche

    Tumoche GBAtemp Regular

    Member
    5
    Apr 30, 2017
    Spain
    I don't know, I can't check rn. But when I was getting the epoxy out, I knocked out some capacitors and scrached the board and when I tried ejecting the drive it tried to eject but it didn't work. Then I soldered one wire to one point that supposedly fixed the tray not ejecting issue but I ripped the pad off (maybe too much heat? it was set at 350°C) .
    At this point I think it's much easing just to buy another board instead of fiddling with the one, as I would have to drill anyway bc it's a windbond.
     
  6. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Yeh, flash the keys to the replacement PCB and you'll be fine.
     
    brickmii82 and Tumoche like this.
  7. Tumoche

    Tumoche GBAtemp Regular

    Member
    5
    Apr 30, 2017
    Spain
    Is it an issue if my drive is 0225 and the pcb i'm buying is 9504? Also where can I find a guide for writing the key to the drive and would I need to install a custom firmware it says it comes with lt2?
     
  8. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Software doesn't matter, hardware does.
    All Phatty drives with the exception of a few and most Slim drives got a new firmware with the 13699 update.
     
  9. Tumoche

    Tumoche GBAtemp Regular

    Member
    5
    Apr 30, 2017
    Spain
    Would this one work? Even through it says it works with dg16d5s, my drive is dg16d4s 0225, is that a problem? https://www.amazon.es/dp/B07QM1NDZN/ref=cm_sw_r_cp_apa_i_wvZrDb2DEM8XB

    Another thing, will I be banned on xbox live?
     
  10. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Get the eBay one.

    Nope, as long as you patch your backups, chances of being banned is slim to none.
     
  11. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Can someone help identify this motherboard? The production date is 2009 Oct, so I'm pretty sure it's a Jasper. But if anyone is familiar please help confirm. Thanks.

    [​IMG]
     
  12. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Jasper or Kronos, remove the CPU heatsink and check the CPU.
    They're both the same when it comes to RGH.
     
    awdrifter likes this.
  13. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Cool, thanks for the info.
     
  14. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    No prob!
     
  15. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Do you still have J-Runner v0.3 Beta 7? I got the Beta 5 from the Xecuter site, but it's crashing. Some error about checking internet.
     
  16. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    awdrifter likes this.
  17. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Thanks for the link. I downloaded that version of the J-Runner, I was able to dump the NAND initially. Then I continue to program the Cool Runner Rev C, then solder in the CR Rev C (bridged JP and 2-3). But now I'm at the point where I'm supposed to connect the JR Programmer V2 to write Xell onto the Nand. It says NAND not found.

    I see that the light ont he JR Programmer V2 is red. I resoldered the wires to the JR Prog V2 and it's still red. I tried writting the NAND anyways but it give me the error "Device Not Found" in J-Runner v.0.5. So I'm not sure where to go now. Did I kill the NAND chip? Or just the JR Programmer V2?

    This is how it looks like with JR Programmer V2 and Cool Runner Rev C installed, power plugged in and JRP V2 plugged into PC.
    [​IMG]

    JR Programmer V2 switches positions.
    [​IMG]

    JR Programmer V2 soldering points, it worked when I first dumped the NAND, so it should be correct.
    [​IMG]
    [​IMG]
     
    zfreeman likes this.
  18. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Console connected to the PSU?
     
    awdrifter likes this.
  19. awdrifter

    awdrifter Member

    Newcomer
    1
    Oct 30, 2018
    Antarctica
    Yes, PSU is connected.
     
  20. DinohScene
    OP

    DinohScene Feed Dino to the Sharks

    Moderator
    23
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    Oct 11, 2011
    Antarctica
    Восторг
    Could you perhaps post the JRunner log?
     
    awdrifter likes this.
Loading...