Homebrew Crash at boot (boot9strap)

[Deleted member 404648]

lemme try

Because I assume that you've had the luma folder and the boot.firm into your SD Card. What you may try is to update your Luma installation on the emuNAND SD card or put the 8.1 boot.firm on the CTRNAND.

--------------------- MERGED ---------------------------

and what i do when i done that?

 

[idiotse]

Go to all the nintendo3ds/xxxxxxxxxxx/xxxxxxxx/extdata/00000000/000000098 (emunand and Sysnand) on Your sdcard and delete this folder 0000098

 

[Deleted member 404648]

Go to all the nintendo3ds/xxxxxxxxxxx/xxxxxxxx/extdata/00000000/000000098 (emunand and Sysnand) on Your sdcard and delete this folder 0000098

i don't have that folder

 

[sp3off]

lemme try


--------------------- MERGED ---------------------------

and what i do when i done that?

Try to launch your emuNAND. all disabled.except the emuNAND boot(even the arm11 thing)

 

[idiotse]

Well i write xxxxxxx but in your case it's named differently Like 176djdhehhbAiue1862929 by exemple

 

[The Real Jdbye]

because dsiware's weren't working also twlauncher didn't work

DSiWare needs to be installed on sysNAND to work, because it reads directly from NAND.
You can install it to both and be able to launch it from emuNAND if your NANDs are linked.
Though there is no reason to keep using emuNAND. You can move your emuNAND to sysNAND by following this guide: https://3ds.guide/move-emunand
Don't do that until you've sorted out the issue though.

 

[Deleted member 404648]

Try to launch your emuNAND. all disabled.except the emuNAND boot(even the arm11 thing)

same crash

--------------------- MERGED ---------------------------

DSiWare needs to be installed on sysNAND to work, because it reads directly from NAND.
You can install it to both and be able to launch it from emuNAND if your NANDs are linked.
Though there is no reason to keep using emuNAND. You can move your emuNAND to sysNAND by following this guide: https://3ds.guide/move-emunand

ehm, how do i do it if i can't even turn on emunand

 

[sp3off]

Enable the "disable arm11 handlers"

 

[Deleted member 404648]

Well i write xxxxxxx but in your case it's named differently Like 176djdhehhbAiue1862929 by exemple

i know... i searched the folder that you said and i didn't find it

--------------------- MERGED ---------------------------

Enable the "disable arm11 handlers"

w8

 

[The Real Jdbye]

same crash

--------------------- MERGED ---------------------------


ehm, how do i do it if i can't even turn on emunand

Don't do that until after you've sorted out the issue.
Anyway, did you try the troubleshooting steps I mentioned yet?

 

[Deleted member 404648]

Enable the "disable arm11 handlers"

black screen...

 

[sp3off]

That is the theme... I don't think that B9S interferes with homemenuhax.

 

[Deleted member 404648]

Don't do that until after you've sorted out the issue.
Anyway, did you try the troubleshooting steps I mentioned yet?

old guide

 

[sp3off]

Try the "firmware.bin" method I've posted before.Or make sure that in Luma, no firmware.bin file is there.

 

[idiotse]

B9s was interferring for me with the same error. Bacause homemenuhax causing trouble

 

[Deleted member 404648]

B9s was interferring for me with the same error. Bacause homemenuhax causing trouble

i had it but i had no prob

 

[The Real Jdbye]

old guide

Huh?

 

[Deleted member 404648]

Try the "firmware.bin" method I've posted before.Or make sure that in Luma, no firmware.bin file is there.

wait

--------------------- MERGED ---------------------------

Try the "firmware.bin" method I've posted before.Or make sure that in Luma, no firmware.bin file is there.

black again

 

[idiotse]

Format your sd card and restart without useless emunand

 

[sp3off]

Hmm, what have you done ?Verifying that no firmware.bin file is here or have you downloaded the firmware + cetk and then put it into "luma" ?