Random question but why not hook up data + and - to the pads on the switch then hook up the reset to vol - and the power button so you could flash it after taking off the usb
Because the switch also generates a usb signal. Hooking it up like this will likely cause intereference and make the usb port useless while the switch is in use. Maybe you could also hook up the 5V from USB, there is als a testpad for that. Then you could flash the Pico while the Switch is off. I would hook up some buttons that will not be pressed at the same time while the console is in use. Otherwise is may cause some unexpected problems.Random question but why not hook up data + and - to the pads on the switch then hook up the reset to vol - and the power button so you could flash it after taking off the usb
tried a different sd card?Hello, thanks for answering, I did what they told me but it didn't work, it doesn't enter OFW, it doesn't let me dump the profinfo with lockpick either, although I was able to make a backup of the nand but it's probably also damaged, I don't know what else to do, the Console was working perfectly before installing the chip, I probably damaged the OFW, I don't know how to recover it, I'm going to cry
tried a different sd card?Hello, thanks for answering, I did what they told me but it didn't work, it doesn't enter OFW, it doesn't let me dump the profinfo with lockpick either, although I was able to make a backup of the nand but it's probably also damaged, I don't know what else to do, the Console was working perfectly before installing the chip, I probably damaged the OFW, I don't know how to recover it, I'm going to cry
yoiu need to hold boot button then plug into pc and drag and drop files, it will unplughow to
how to flash unlock.bin? and what page here also I can find the file.copy and paste file into that folder
hey what fw did u flash ? i hab almost the same issue with the compressed fw2.5+ulock from @vittorio if u are also using this do me a favor and try to flash the fw2.5nw.uf2 and after that the unlock.uf2 after that everything worked fine for mehello, I was finally able to boot the chip, check the soldering and that's it, but now I wanted to test OFW, check that the connection between the points and the pico fly have 47ohm resistance. I don't know what else I could check pkg1 decryption failed bek is missing
I forget what points there called but the 2 top right ones hook one to vol minus and the other to the power button on the ribbon cableActually you need a way to reset the chip to enter uf2 mode, that is how it is on Trinket M0 that also use UF2.
Because the switch also generates a usb signal. Hooking it up like this will likely cause intereference and make the usb port useless while the switch is in use. Maybe you could also hook up the 5V from USB, there is als a testpad for that. Then you could flash the Pico while the Switch is off. I would hook up some buttons that will not be pressed at the same time while the console is in use. Otherwise is may cause some unexpected
Rcm mode maybeBecause the switch also generates a usb signal. Hooking it up like this will likely cause intereference and make the usb port useless while the switch is in use. Maybe you could also hook up the 5V from USB, there is als a testpad for that. Then you could flash the Pico while the Switch is off. I would hook up some buttons that will not be pressed at the same time while the console is in use. Otherwise is may cause some unexpected problems.
will check all the values a bit later, here you can take the required caps for the CPUI'm sorry to bother you again. I'm currently working on soldering a MOSFET, but the capacitor on the mounting point came off. Is it not recommended to directly connect a wire to the pattern in this case? Do I need to buy a new capacitor?
You can leave the capacitor off and connect the leads without it. The CPU will probably still work as these capacitors are usually redundant to improve reliability. Do not just put any capacitor there without knowing the required value. The CPU will not be damaged by leaving the capacitor off.I'm sorry to bother you again. I'm currently working on soldering a MOSFET, but the capacitor on the mounting point came off. Is it not recommended to directly connect a wire to the pattern in this case? Do I need to buy a new capacitor?
I don't think you are supposed to bridge these pads. You are only supposed to use one of them each. Look at the instruction photos.
I get blue then pink flash and ofw but cmd/clk is fine?
Reset the chip - short the 2 pins near usb portAnyone knows an fix to this:
My switch oled with hwfly v5.3 has this error purple breathing to green static (only Pressed Power Button) purple breathing to green breathing (Pressed Power and +) without sd card i get into hekate (without sd Mode)
Anyone knows this Issue?
You can bridge them they are on the same trace - bridging them also helps securing them betterI don't think you are supposed to bridge these pads. You are only supposed to use one of them each. Look at the instruction photos.