Xk3y Reloaded, no blue light and more

Discussion in 'Xbox 360 - Hacking & Homebrew' started by Henrik, Nov 21, 2013.

  1. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    Hello. My Phat LiteOn xbox 360 doesn't cooperate with me as it should.

    The problem is when I boot the xbox 360 with xk3y installed and the SDcard plugged in the blud light doesn't light up, but when booting without the SDcard it does light up.

    The red light on the xk3y is always lighting

    When trying to press ''Open Tray'' the cycle doesn't work, it gets stuck on ''Close Tray''

    Any ideas on what could be wrong?
     
  2. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    Have you converted your drive FW dump to a stock firmware (instead of a PhatKey extract)?
    Have you formatted your SD card? (this will wipe the linux partition, which you want to keep for the Xkey to operate)
    Have you hooked it up correctly?
     
  3. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    1: I'm not sure what you are referring to. I followed the Xkey Manual, is there another way of dumping the Stock Firmware? My drive is flashed with LT+3.0 for your information.
    2: Yes, done this a lot of times, with the guide provided by The Artificer in the k3y forum. I had the 1 RROD problem once.
    3: Yes, have re plugged it as well just in case something went wrong, everything is hooked as shown on the Manual. Even looked at the Video tutorial. I have also insulated the Xk3y.

    Thanks for reply
     
  4. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    You probably don't have the correct firmware dump, you'll need to convert your firmware dump to a stock firmware with Jungleflasher.
    If you don't know how to do it or don't have a stock firmware dump then I could do it for you.
     
  5. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    How could you do it? I would like to have it fixed ASAP :) I used the PMT to take out my key on the LiteOn drive, I got the Dummy.bin, put it in the above section, used the original as targeted saved it as firmware.bin. Is it because its a flashed Xbox 360?
     
  6. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    You'll need to convert it to a stock 02510c FW
    Then save it either as firmware.bin or dummy.bin
    If both won't work then I'd return the Xkey (could be faulty)
     
  7. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    May I ask you to explain how to do it? As far as I know I've tried doing this, or something similar.
     
  8. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    You'll have to get the firmware pack from Xbins (I can't give it to you since it's copyrighted material)
     
  9. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    I have a firmware pack from Ixtreme, isn't that enough?
     
  10. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    If it contains a stock firmware then yes.
    Otherwise, nope.

    Jungleflasher must recognize it as a stock firmware, not a PhatKey extract.
     
  11. Henrik
    OP

    Henrik Member

    Newcomer
    10
    0
    Nov 14, 2013
    Okay, I have a flashed LiteOn with LT+3.0.

    Ill take my Dummy.bin which I extracted from the Driver as Source.
    Then I take the stock firmware named orig-02510C-1c000.bin as Target.
    Then I Spoof to Target and save the file as firmware.bin and put it in the root of the Micro SD card.

    This didn't work, the blue light was of, didn't flash or was solid, and a red light was solid on the xk3y.
    I have also gotten 3 RROD now, but that should be easier to fix.

    What am I doing wrong? If it is possible, could we chat on Skype?
     
  12. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,592
    11,959
    Oct 11, 2011
    Antarctica
    В небо
    Humm, I think you got the wrong firmware file.
    Aye, PM me your skype adress and I'll add you ;]