Well, you can't exactly fit a backup of your NAND into your NAND. Also, it would be nonsensical to backup the NAND onto your NAND. I mean, how would you access it?Hi.
When I backup my nand it's normal they get stored to the root of SD card?
Thank's
I mean structure folder.Well, you can't exactly fit a backup of your NAND into your NAND. Also, it would be nonsensical to backup the NAND onto your NAND. I mean, how would you access it?
Yes
Your card partition is probably. Did you remove switch back before? Normally these errors come from the 1bit bus width (hekate drivers do not support it).
Your card, of course, supports 4bit wide. But it can fallback if some data pins are not connected.
Can you try to press and hold the connector for the sd card reader and try and make a dump of BOOT0/1?
I used Hekate to launch ChoiDujour and updated my firmware to 5.1 from 5.0. It was successful but now I can no longer charge or send signal to HDMI. I get a green blinking light on the dock. The only way I can charge is if it's connected to computer, my PC detects the switch fine. I can boot fine and play backups without any issues. I don't know what to try and I don't want to make the situation worse.
Doesnt really matter. I can insert my SD while in RCM mode just fineIf auto-rcm is enabled and you ''power off' switch from os, is it safe to remove SD card at that point while back in rcm (before any payload sent), or should it be fully powered off by sending payload, and powering off through hekate first?
You don't install it. It's a payload.
This should teach you the basics from booting into RCM to how to send payloads via USB connection.OK then. . please. may you give a guide on how to load this?
This happens when you don't have an sd card normally. If you have, what's your hekate ini?I get this error message when I change the verification options
I was able to make a backup just fine. I don't have anything hekate related on my SD though (?) The only thing I did was push the payload and make a backup. Nothing added to the SD card myselfThis happens when you don't have an sd card normally. If you have, what's your hekate ini?
Okay I will take a look! Thank you!I c. This depends on hekate_ipl.ini.
It is up to date and will always be. Everything that writes the emmc is considered dangerous by me.About to use Hekates Restore Nand option so that I can start using 2 different Nands, one for regular use online gaming and one for homeBrew and offline gaming only. Anything I need to know before I try to do a restore? for example, is this text up to date and what does the "10 second mandatory wait time" mean?
"Restore eMMC RAW GPP (Dangerous!):
Do not use that if you don't know what you are doing! No one is responsible for messing with your device.
You have a 10 second mandatory wait time before letting you start restore by pressing POWER.
This let's you restore your eMMC general purpose partition. If hekate find the /Backup/Restore/rawnand.bin it will restore it and verify it.
If it does not find it, it does nothing.
For now only exFAT is supported. No partial restoring."
Also, seeing as my Switch is not bricked or anything, do I actually need to restore boot0/1 aswell?
It is up to date and will always be. Everything that writes the emmc is considered dangerous by me.
A full backup is boot0/1 and rawnand.bin. Boot0/1 have unknown data written to them in every boot. So..
The text is to make sure you don't press that by mistake.
Yeah. Generally, I try to end folders with a "/" to distinguish them.Thanks, I'll try and take my chances for now. I don't intend to do this to often of course.
Just to make sure that they are not skipped then:
"This let's you restore your eMMC BOOT0 and BOOT1 partitions.
It will only restore the files at /Backup/Restore/BOOT0 and /Backup/Restore/BOOT1."
In this case "BOOT1" and "BOOT0" are not folders containing the boot files, but actually the boot files themselves, right?