Picofly AIO Thread

[Acide0]

No. Updates are done via an updater Payload that you launch i.e. from Hekate, then select the file to flash.

Thank for the answer that’s a great thing so I will flash the 2.6a.

 

[Dee87]

Thank for the answer that’s a great thing so I will flash the 2.6a.

keep in mind 2.6 is still alpha i have it runing on my oled and v2 no issues

 

[metalex201]

all ur answer are answered in the first page of this thread except for the pico.
u can use it but u would need to eather cut it with a risk because the layers in the pcb or u put it outside or just order a rp2040 or one of the others wich are supported with 2.6 alpha

Apologies i didnt refresh and it only showed the older thread that didnt have the updated description. Is the "RGB mode" jumper the one i would need to connect the neopixel to?

 

[3CP-andres-N]

Colleagues, with the release of version 2.6, some peaks have already been enabled, here you have the scheme of the installation points of this

 

[Phantomas77]

Colleagues, with the release of version 2.6, some peaks have already been enabled, here you have the scheme of the installation points of this

You just asked this HERE Why spamming? You won't get the answer faster...

 

[impeeza]

and also on the 2.6 release is the description of the pins of each supported board!

 

[LogicalMadness]

Maybe now:

amazon.com/dp/B08RYMY6XK/ref=as_sl_pc_tf_til?tag=&linkCode=w00&linkId=&creativeASIN=B08RYMY6XK

 

[Adran_Marit]

and also on the 2.6 release is the description of the pins of each supported board!

which is in the first post XD

 

[crazycrash_hum]

Hi I'm wondering why soldering points for oled is not in the front page ?

Thank you

 

[Adran_Marit]

Hi I'm wondering why soldering points for oled is not in the front page ?

Thank you

Good question, I've yet to see any good diagrams, however they do use the same points as the HWfly chips. if you have a good image of the points in question I'm happy to add it

 

[Donnie-Burger]

Good question, I've yet to see any good diagrams, however they do use the same points as the HWfly chips. if you have a good image of the points in question I'm happy to add it

 

[Dee87]

was about to do the same

 

[Adran_Marit]

was about to do the same

cheers lads, added to the solder points tab

 

[blanks]

i cant seem to get 2.6a to work with a waveshare rp2040 zero. I can seem to flash it onto the rp2040 ok, but no leds to confirm and doesnt boot hekate. I've put 2.5+unlock back on and its fine again. anyone know what might be wrong?

ah nvm i tried 2.61 and it works as expected.. just didnt want to be on an old fw before removing the usb socket!

 

[cicci084]

I can't find the 2.61 firmware, where can I get it?
Edit, found in the top root of github.
The link in the first post leads to the firmware folder, however there is only alpha version 2.6 inside and not 2.61

 

[FlowerFire]

Hi guys, I see the eMMC solder points in OP are listed as V2. So I guess I can't use them even though it looks just the same?
I'm in a desperate need of a different 3v3 point for my install

 

[Dee87]

Hi guys, I see the eMMC solder points in OP are listed as V2. So I guess I can't use them even though it looks just the same?
I'm in a desperate need of a different 3v3 point for my install

emmc solder point on v2 are the same as on v1

 

[FlowerFire]

emmc solder point on v2 are the same as on v1

That's good news, thanks. Can i bridge those two 3v3 points or do I have to solder to a single one of them?

 

[Acide0]

Hi, I have do a install of a rp2040 zero on a switch light, I'm not at my first I have done a lot of sx/hwfly install.
I have 2 rp, one that I have flash wit 2.5 with the unlock include, and the second one with the 2.6a on this one I need to strap the 2 point on the back.

with the 2.5 I have my green light but nothing on screen just a black screen and with the 2.6 I got my red light but again blackscreen. If I remove everything the switch start normally. My emmc is a samsung.

What I should try to got a boot ? Thank you for your answer


Edit: I have found my problem, I was taking the ground from a coil and this is why it,s doesn't boot, now that I take ground from a cap everything fine !

 

[cicci084]

Guys, I installed the rp2040 chip (fw 2.61).
I attach photos.
I can't find the guide to finalize in the first post but edit and prepare the sd and all the rest.
I'm stuck on the screen below. (see attachments).

Also posting the work I've done, I'd accept suggestions for improvement. Thank you