Picofly AIO Thread

[snake2]

Updating from 10.x.x to 16.0.1 fixed my BOOT0 after it got corrupted by unlocking

On Hekate selecting reboot to OFW gave a black screen but I was able to use Atmosphere to boot stock then update over internet

 

[Battlegames]

is possible to use v2 cpu cable on lite and oled?

 

[Adran_Marit]

Updating from 10.x.x to 16.0.1 fixed my BOOT0 after it got corrupted by unlocking

On Hekate selecting reboot to OFW gave a black screen but I was able to use Atmosphere to boot stock then update over internet

yes, because you booted full stock it fixed the boot0. This is mentioned in the FAQ

 

[urherenow]

It's not mentioned in the FAQ, but in the "Hints" link. I had to hunt for that one.

 

[Adran_Marit]

It's not mentioned in the FAQ, but in the "Hints" link. I had to hunt for that one.

Yeah it is

• If rebooting to OFW vol buttons don't work and blue or black screen
  • boot into full stock and perform full system reset

edit: my bad. I knew I had it in the op, just had the wrong tab.

 

[urherenow]

Yeah it is

Ummm... yea... in the Hints link, just as I said (and as you quoted). Not under FAQ.

 

[Adran_Marit]

Ummm... yea... in the Hints link, just as I said (and as you quoted). Not under FAQ.

As I said my bad, I did know the information was in the OP though

 

[urherenow]

As I said my bad, I did know the information was in the OP though

It's all good. I was just trying to clarify. I'm OCD'ish... or maybe just straight up OCD...

 

[Dandan0404]

Should I put Normally Open reed switch in PINS 1 AND 2? so that when magnet comes, it triggers reset?

 

[rskL]

Edit. This post was messed up

 

[jkyoho]

Does anyone know of I get this stuff I'll be set to do this? Anything else I might need

Already have the resistors, flex cable and the rp2040

YOU should be good if you not plan to remove the RP2040 USB-C port otherwise another larger soldering tip for removing the port helps.(unless you have hot air station)

 

[wscp]

Wherre is the 3v3 point for lite?

 

[808080]

Wherre is the 3v3 point for lite?

look

 

[Kyle46791]

Does the Toshiba firmware come unlocked already or will I need throw the unlock.uf2 on that too?

 

[Donnie-Burger]

Does the Toshiba firmware come unlocked already or will I need throw the unlock.uf2 on that too?

Flash toshiba uf2 then flash unlock uf2

So far confirmed working on my end

V1 patched Erista
V2 Mariko

Both with hwfly flex cables
47 - Ohm resistors

 

[papafria]

Hello Dudes!! I really don't know what to do anymore. The picofly sometimes boots and sometimes and sometimes not. I have never get the green blink.. Similarly, despite being able to get hetake to run, I am unable to run atmosphere. Does anyone have any clue as to what's going on? The device is in the latest version, 16.0.1.

 

[JackFrostSMT]

Hello Dudes!! I really don't know what to do anymore. The picofly sometimes boots and sometimes and sometimes not. I have never get the green blink.. Similarly, despite being able to get hetake to run, I am unable to run atmosphere. Does anyone have any clue as to what's going on? The device is in the latest version, 16.0.1.

Looks like your rgb colors are flipped. Try toggling the jumper on the back

 

[papafria]

Looks like your rgb colors are flipped. Try toggling the jumper on the back

what do you mean with toggling the jumper dude? and what jumpers exactly?

 

[JackFrostSMT]

what do you mean with toggling the jumper dude? and what jumpers exactly?

Look at the installation diagrams for the rp2040, GRB/RGB jumper
If you have it bridged already like I did, unbridge it
If you don't have it bridged, then bridge it

 

[papafria]

Look at the installation diagrams for the rp2040, GRB/RGB jumper
If you have it bridged already like I did, unbridge it
If you don't have it bridged, then bridge it

Thanks Dude... You are the best.. Thats resolve my 1st issue... But now, i dont know why sometimes Success and Sometimes i get the code of Bad CPU pin..

I dont know what to do because of 10 attempms, 5 success and 5 bad cpu pin (without moving anyting)...

I am ussing 2 mosffet IRFHS8342 (1 per each Cap)... Should i use only one?

This is a LCD V2....

¿Any Ideas?