i have 2 oled with instinct but the older oled 2023 dont have this issue and the new one 2024 oled has, what happened?
When I enter the EMUMC partition, the official system and Syscfw system I watch the screen show two white color lines time appearance logo atmosphere logo and show the official Netindo screen logo and does not appear something checked Points and check DAT0 cleaning Motherboard Nothing There is nothing but this thing is not separated if you separate the CPU Point wire in the RP2040 CHIP widget ... Please answer this error in Boot Chip.
Cfw ofw emummc 18.0.1 hats pack 17.0.3
I have video.. You can see one line frist inter emummc and after logo atmosphere...
Cfw ofw emummc 18.0.1 hats pack 17.0.3
I have video.. You can see one line frist inter emummc and after logo atmosphere...
Last edited by Danook28,
If you go and check previous messages they already mentioned that it is normal.
yes but I want to know why this happens because not everyone experiences it even with same chip or not
If you want to know, then you need to buy some Logic Analyzer or Oscilloscope then you need to find a way to clip pin in the oled connector, and find some unusual signal. Then you trace back what line produce those unusual signal, it will ended on some ic or resistor or capacitor. You test one by one, maybe by removing it, and check whether the unusual signal produce or not. Then you found your 'reason'.
For me, thats wasting time. As long as its work, and not interfering with me enjoying the game, then all is good.
Attachments
It doesn't seem any easier or cheaper than just running wire. So what's the benefit? Is it faster?
To me it just looks like an easy way to accidentally rip DAT0 point.
To me it just looks like an easy way to accidentally rip DAT0 point.
Lollll, i was just thinking the same thing
. it is a lot easier to do it with a thin wire. Done more then 30 kamikaze with just a stripped thin wire without any trouble.
It doesn't need cutting on the OLED. Fits perfectly next to the heatsink on top of the ram.
It doesn't depend on the modchip, in my case (RP2040-zero) I thought it was the modchip that was the problem and I replaced it but nothing has changed.
Among other tests, I also removed it and the console no longer showed the line.
Of course I checked the flat video as well... perfect. In my opinion it's a bug in the code on the video refresh because it appears when the video is reset on the screen
Similar threads
-
-
-
@
Morganna:
i dont want to sound silly, but im kind of lost, im new to this community and i have a lot of question and idk where to start -
-
-
-
@
Sicklyboy:
Can't wait for the inevitable power outage where it's initially funny because I have half of my apartment on UPSes, then I realize I have literal minutes to start shutting down all of my servers. -
@
BigOnYa:
You must be north of me, Im in Ohio.. It been storming on off all day here, coming from the north -
-
-
@
Morganna:
@BigOnYa well, starting with, idk which emulator should i use for switch, i got a gtx 1650, do you know which one would it better for my pc?
-
@
BigOnYa:
The switch emulators on pc rely on your CPU mostly, and they only use a single core, so GPU not as important as a good CPU. I don't use switch emulator, but many here do, and willing to help.
-
-
@
BigOnYa:
@Morganna I'd say try them both, and see which work better for your setup, good luck, and have fun!
-
-
-
@
BigOnYa:
No you are not allowed to discuss them here, against the rules of the site. Sorry. But you can Google Nintendo NSP and there will be a few listed.
-
-
-
-
-
-
-
-
