Hacking Hardware Picofly - a HWFLY switch modchip

[abal1000x]

.

 

[Danook28]

I am sure led is white and short pulsed

I think you damge the lcd conector pin inside is fulty. Try see with microscope.

 

[Browbon]

do i need to cut the shield when install pico on V2? i have seen a perfect fit place on lite but i have no idea with V2

 

[Danook28]

do i need to cut the shield when install pico on V2? i have seen a perfect fit place on lite but i have no idea with V2

You can do it with out cut any shell brother.

Post automatically merged: Jun 5, 2023

The instinice v6 chip back again. With low price.
https://a.aliexpress.com/_mNrZpNa

 

[rehius]

I don't know where is the backlight pin in the oled

OLED is a kind of a display without backlight, every pixel is lit independently

 

[Danook28]

OLED is a kind of a display without backlight, every pixel is lit independently

You hearing sound back menu or try docking tv wile glitch pico????

 

[abal1000x]

.

 

[Browbon]

You can do it with out cut any shell brother.

Post automatically merged: Jun 5, 2023

The instinice v6 chip back again. With low price.
https://a.aliexpress.com/_mNrZpNa

do you have any examples of it? it is helpful when see some installation without cutting the shield

 

[fox87]

You can do it with out cut any shell brother.

Post automatically merged: Jun 5, 2023

The instinice v6 chip back again. With low price.
https://a.aliexpress.com/_mNrZpNa

Is there a thread showing all the Spots?

Where did you get the picture with the voltages from?

 

[Danook28]

Is there a thread showing all the Spots?

Where did you get the picture with the voltages from?

Voltage for what????

 

[deeps]

do i need to cut the shield when install pico on V2? i have seen a perfect fit place on lite but i have no idea with V2

it's possible to route wires through the fan hole and mount the chip on the outside of the shield. Many people prefer cutting a hole in the shield though because it makes the install easier and the chip can then be mounted in the "usual" spot on top of the ram shield.

 

[Danook28]

do you have any examples of it? it is helpful when see some installation without cutting the shield

One mosfet can working perfectly.mate

 

[sleeperonair]

yes usually only 1 is work.
But theres report people in here whose said sometimes need 2 mosfet.
I myself never meet that cases. 1 mosfet is enough.

But, it could be that the mosfet you use are broke, thats why i suggest using both. If you could check the condition of the mosfet is better. Make sure the mosfet is work, makesure its connected to the cap.

tried 3-4 and to the resistor, Value 0 for the flex on pico. why does rst show first 1200 and then 1, is it because of the processor flex?

 

[Danook28]

tried 3-4 and to the resistor, Value 0 for the flex on pico. why does rst show first 1200 and then 1, is it because of the processor flex?

If you want see the value of Flex v2 i have one mate.

 

[sleeperonair]

If you want see the value of Flex v2 i have one mate.

can u ask him please?

 

[Danook28]

Oh yes you're right, dang i forgot.

Brother i have lite console and picofly install inside and Flex Cable v2. If you want me to read any capacitor or point!! Mate

 

[sleeperonair]

Брат, у меня есть облегченная консоль, внутри установлен picofly и гибкий кабель v2. Если вы хотите, чтобы я прочитал любой конденсатор или точку! Приятель

rst and flex on pico

 

[abal1000x]

.

 

[Danook28]

rst and flex on pico

Rst /0.398 v up to (1.411 v) diode mode
Sp1 / 0.10,7 ohm sp2 0.10,7 ohm diode mode
Flex Cable with out capacitor install is
Sp1 sp2 drine (D) is 0.392 v in diode mode.
The ps1 sp2 ground point in diode mode 0.1 ohm beep long.

 

[bilalhassan341]

yes usually only 1 is work.
But theres report people in here whose said sometimes need 2 mosfet.
I myself never meet that cases. 1 mosfet is enough.

But, it could be that the mosfet you use are broke, thats why i suggest using both. If you could check the condition of the mosfet is better. Make sure the mosfet is work, makesure its connected to the cap.

In my case the first two switches needs the two mosfet. And one of them still require a SDA SCL wire with two mosfet. I don't know if I have a low quality one. I encountered one switch that require the single mosfet but with SDA SCL wire.

Edit: Now, I'm thinking about using a AON7506 mosfet. No more 8342 mosfet.