Still cheaper using picofly. Its cost effective, and performant wise.Well at this price I've bit the bullet on behalf of my partner and purchased this at a mere £22
View attachment 363326
Certainly hope we've done the right thing
The price seems very fair in my very humble opinion
Can you share image install of mosfet? thanksTried with RP2040-zero on my Switch Lite. Stable work for a week now, no issues.
Works well with 47R resistors (samsung emmc) and IRFH3707 mosfets. Two mosfets set in parallel and soldering to two capacitors on CPU. With a single mosfet there was cyan light all the way. I guess any comparable mosfets (8-10 amps and low voltage gate) should work if you cant find OG's.
Also, anyone knows better point to get 3v3 on switch lite? Point on small cap under flex conn is pain.
Yea looks very sketchyJust pointing out that so far this place has next to no orders and the original "official" store is 50% more expensive. Hopefully it's legitimate.
Open question: ignoring price, objectively is this Instinct chip better or worse than a well installed picofly?
good bye have fun XdMight bail on this if this works on a mariko
it all depends on what u want to pay and how much work u want to put in.So what is the current best chip for OLED? I’m a bit lost with all the different versions.. I will be installing these chips for the first time on mine and a friends OLED. Will need to ship to UK
LED doesn't blink after flashing on a Waveshare 2040-zeroNOT tested, so NOT putting into the main post (will be updated once I test everything).
no guarantees, use at your own risk.
for those who can't wait
!!!!PINOUT!!!! (resistors / mosfets are still required)
Common GPIO for all boards:
CMD => 28
CLK => 27
RST => 26
Waveshare 2040-zero / 2040-one (default, floating pins 29, 11, 16):
DAT => 29
CPU => 15
Raspberry Pi Pico (detected by thermal sensor on pin 29):
DAT => 22
CPU => 21
XIAO2040 (detected by LED power on pin 11):
DAT => 29
CPU => 6
Adafruit ItsyBitsy (detected by LED power on pin 16):
DAT => 29
CPU => 24
ChangeLog:
- fixed regulator setup
- firmware update feature (+ rollback to backup in case of non-working fw update)
- multiple boards support (no idea if that works, magic, ensure LED blinks after write! that means detection worked fine!!)
- extended OFW support, should not break BOOT0 anymore, OFW BCT is copied into the unused space
P.S. I need some rest.
set rgb mode should fixLED doesn't blink after flashing on a Waveshare 2040-zero
no alternativ solder points for Dat0 On Led well actually ther is one but u would have to drill a whole in the board but i wouldnt rick doing it XdGood morning everybody.
Exist any alternative solder point Do OLed NAND ??
Thanks
Post automatically merged:
Good morning.
Exist any RST alternative solder point in OLED NAND?
Thanks.
did u check all the pins?I've disconnected the flex and checked the flex.The continuety is there up to the mosfet.No problem there.
Post automatically merged:
I'm using a felx cable form the hwfly v2 flex and has 2 mosfets
Lol they just jacked the price after couple of ordersReally not entirely sure tbh, here's the product https://www.aliexpress.com/item/1005005412303511.html?
Also its a random selling store. Nothing focused on one thing. Never the less, buyer protectionLol they just jacked the price after couple of orders
need to set RGB jumperHello. I'd like to thank the devs for this great job. One question if I may: When I flashed my rp2040 and re-plugged it. It gives a blue light then white, I saw a video on YouTube where it shows a purple color, not white. Am I good or is there something wrong? Video attached, Thanks.
I paid with PayPal so have some buyer protection there, so even if it doesn't arrive I'll have some supportLol they just jacked the price after couple of orders
Can you show the mosfet diagram please?Tried with RP2040-zero on my Switch Lite. Stable work for a week now, no issues.
Works well with 47R resistors (samsung emmc) and IRFH3707 mosfets. Two mosfets set in parallel and soldering to two capacitors on CPU. With a single mosfet there was cyan light all the way. I guess any comparable mosfets (8-10 amps and low voltage gate) should work if you cant find OG's.
Also, anyone knows better point to get 3v3 on switch lite? Point on small cap under flex conn is pain.
yes that was meand one that even laughed at my post
yes that was me
why because if funny how the prices have been dropping the last couple days
Hello. Thank you for replying on such short notice. Excuse my ignorance but could you tell me how? Thank you!need to set RGB jumper
on the first page are the instructions, also on the important post at top of pageHello. Thank you for replying on such short notice. Excuse my ignorance but could you tell me how? Thank you!
Hello. Thanks.on the first page are the instructions, also on the important post at top of page