We can remove this caps and the switch will still works without any problem?looks fine, BUT ensure your rp2040-zero is fully connected and working (blue light).
I had such smoke several times when forgot to solder the GND wire
We can remove this caps and the switch will still works without any problem?looks fine, BUT ensure your rp2040-zero is fully connected and working (blue light).
I had such smoke several times when forgot to solder the GND wire
So all the wires can overlap and touch one another with no issues?yeah but they all connected to each other so bridging shouldnt be an issue.
Wires cannot touch. I was referring to the double points.So all the wires can overlap and touch one another with no issues?
Oh got itWires cannot touch. I was referring to the double points.
Even better, thanks.yeah but they all connected to each other so bridging shouldnt be an issue.
I just got the mosfets from digikey, theyre about $.50 a piece
Ordered resistors too but they ended up being 47K and not 47ohm which is what prompted me to salvage them. Other than looking at what boards you have or checking schematics if available, I think it might just be easier to order them. Especially since the ones that are recommended are specific models and not just any old mosfet.
Yeah it works fine.We can remove this caps and the switch will still works without any problem?
wrong diagramJust to confirm this is the route I went down.
Have hekate or your atmosphere bins named as payload.bin on the root of the card, obv copy any other files they mightve came with in the zipJust to confirm it boots 1 in every 20 odd times on the switch lite so I have left those both aside. Now v2 have it working instantly every single time but I get the hekate failed to open payload.bin
What is the correct sd card setup for this as I have tried everything including using a sd card backup from my working V1 trinket build and fresh setup of hekate and atmosphere. Also if anyone sees this message and is struggling, V2 wire sizes don’t matter iv tried multiple and all get the same result, I have found that soldering directly to the cap is the best option though.
See attached image of correct method for V2 tested working.
Just to confirm it boots 1 in every 20 odd times on the switch lite so I have left those both aside. Now v2 have it working instantly every single time but I get the hekate failed to open payload.bin
What is the correct sd card setup for this as I have tried everything including using a sd card backup from my working V1 trinket build and fresh setup of hekate and atmosphere. Also if anyone sees this message and is struggling, V2 wire sizes don’t matter iv tried multiple and all get the same result, I have found that soldering directly to the cap is the best option though.
See attached image of correct method for V2 tested working
you have to download the last hekate.bin file and rename it payload.bin and copy the payload.bin on the root of your sd cardJust to confirm it boots 1 in every 20 odd times on the switch lite so I have left those both aside. Now v2 have it working instantly every single time but I get the hekate failed to open payload.bin
What is the correct sd card setup for this as I have tried everything including using a sd card backup from my working V1 trinket build and fresh setup of hekate and atmosphere. Also if anyone sees this message and is struggling, V2 wire sizes don’t matter iv tried multiple and all get the same result, I have found that soldering directly to the cap is the best option though.
See attached image of correct method for V2 tested working.
Yeah I did that and it wasn’t this. The issue was the sd card reader wasnt plugged in correctly lolHave hekate or your atmosphere bins named as payload.bin on the root of the card, obv copy any other files they mightve came with in the zip
This looks like a V1 to me, not V2.Just to confirm it boots 1 in every 20 odd times on the switch lite so I have left those both aside. Now v2 have it working instantly every single time but I get the hekate failed to open payload.bin
What is the correct sd card setup for this as I have tried everything including using a sd card backup from my working V1 trinket build and fresh setup of hekate and atmosphere. Also if anyone sees this message and is struggling, V2 wire sizes don’t matter iv tried multiple and all get the same result, I have found that soldering directly to the cap is the best option though.
See attached image of correct method for V2 tested working.
Hi,
Is there a need for two parallel np2016 mosfets (Like there are on hwfly flex for v2 mobos) instead of one IR... Mosfet for mariko?
Or one np2016 will be enough?
Thnx 4 reply.
EristaThis looks like a V1 to me, not V2.
First cap is vertical not horizontal
Can that pad be used for dat0 on v2?Just to confirm it boots 1 in every 20 odd times on the switch lite so I have left those both aside. Now v2 have it working instantly every single time but I get the hekate failed to open payload.bin
What is the correct sd card setup for this as I have tried everything including using a sd card backup from my working V1 trinket build and fresh setup of hekate and atmosphere. Also if anyone sees this message and is struggling, V2 wire sizes don’t matter iv tried multiple and all get the same result, I have found that soldering directly to the cap is the best option though.
See attached image of correct method for V2 tested working.
My image looks like it’s soldered there but it isn’t. I have come off the boards connector for Emmc pins so I can remove and upgrade the Emmc size later. This was just a test run to see what’s the best route to take when doing this with wire size, locations and placement etc. I’m in bed now but can go over with multimeter later and find more alternative pads.