Here we go, some proof it acctually works.... Just to nip this in the bud
Here we go, some proof it acctually works.... Just to nip this in the bud
I'm not the only person that has successfully installed in here... I will install one in my oled to prove a point if I have to...No, I don't think it's fake, I think it's an old and flaky firmware and you got lucky for some reason we've yet to determine.
I'm the Midlands vinceTafty - if you had a blue mat there I'd swear you were My Mate Vince
We know it can work, that's not in question.Gentlemen it's useless to get lost on the diagrams, it works, it doesn't work.....everything works perfectly I'm testing it on mariko do you want my video too? the firmware is missing we have to focus on that
Can I ask have you tried using a hwfly/sx to confirm you have installed right.We know it can work, that's not in question.
Here we go, some proof it acctually works.... Just to nip this in the bud
How I did what exactly???I would find it nice if you would make an video and Show how you did it.
And what files did you used?How I did what exactly???
I used the install picture from page 34...
Yeah OFW is working as long as I disconnect the chip, I'll do a more thorough investigation later today. Would you mind grabbing diode mode readings? That'll be helpful for troubleshooting. I'm wondering if the values would be the same as with HWFLY or if it's affected by the presence of the chip in any way.Can I ask have you tried using a hwfly/sx to confirm you have installed right.
Does it still boot into OFW correctly
Originally when I installed into the lite I couldn't get the sx to load, would fail to glitch... I put the rp in and was getting the yellow led(dat0) sure enough I had accidentally grounded dat0 against the cover directly next to it.
I have a lite working, kingdede has a mariko, the only one we haven't tested is an oled... But I'm happy to pull my oled apart to test this just to prove it works if needs be.
I have a mariko I could test on aswell if its really needed.
The file is also on page 34, remove the .pdf from the end since .uf2 can't be shared directly on the forumAnd what files did you used?
The Ubuntu uf2 which is also on the same post on page 34!!!!!!!!!!!!!!!!!And what files did you used?
When I'm back at my desk later I will happily take them for youYeah OFW is working as long as I disconnect the chip, I'll do a more thorough investigation later today. Would you mind grabbing diode mode readings? That'll be helpful for troubleshooting.
The file is also on page 34, remove the .pdf from the end since .uf2 can't be shared directly on the forum
Where did you get the software flashed on the rp2040 ? Thats what i meantThe Ubuntu uf2 which is also on the same post on page 34!!!!!!!!!!!!!!!!!
Post automatically merged:
When I'm back at my desk later I will happily take them for you
Page 34 like I said, the uf2 file is attached to the same post the install diagram is.Where did you get the software flashed on the rp2040 ? Thats what i meant
You will need to trim the metal heatshield the same as sx or hwfly, you may be able to squeeze it under BUT there is a big risk of shorting it out as there is a voltahe regulator on the bottom and obviously exposed points on the topanyone with this chip installed in mariko can inform if have space inside to put the chip?
in the diagrams,appear one component solder directly to cpu, i think that was the mosfet.Page 34 like I said, the uf2 file is attached to the same post the install diagram is.
I plugged the rp into my pc in boot mode(holding the boot button) then copied the uf2 on to the rp internal memory... Job done
but if i use kapton tape, don´t eliminate the risk of shorting?You will need to trim the metal heatshield the same as sx or hwfly, you may be able to squeeze it under BUT there is a big risk of shorting it out as there is a voltahe regulator on the bottom and obviously exposed points on the top
Yep the flex has mosfets on it allready, just bridge pin 3 and 4 onto the end of the flex and solder your wire to them, be careful around pin 1 2 5 6 as these are grounds.in the diagrams,appear one component solder directly to cpu, i think that was the mosfet.
if i use a flex cable (v2), don´t need that right?