Hardware Component Identification needed, chokes by P13USB

[fnwhatnow]

Could somebody tell me what this is called so I can order some?

They are right above:

Thanks!

 

[Pintglass]

Could somebody tell me what this is called so I can order some?

Part number EXC24CS350U

https://www.mouser.co.uk/datasheet/2/315/AWE0000C294-1283909.pdf

 

[FXDX]

From here I bought it and it works perfectly.

https://ro.mouser.com/ProductDetail...=sGAEpiMZZMsVJzu5wKIZCVmiNDXvL6WFCSe53ELiIcQ=

 

[Chai_tea]

By any chance, you would know the brownish components right beside it? I happened to knock mine off while attempting to replace the P13USB

My assumption is that it is one of those ceramic capacitors, but I don't know the spec of it.

 

[Pintglass]

By any chance, you would know the brownish components right beside it? I happened to knock mine off while attempting to replace the P13USB

My assumption is that it is one of those ceramic capacitors, but I don't know the spec of it.

Which caps have you knocked of post an image, as there different values

 

[Chai_tea]

Which caps have you knocked of post an image, as there different values

These four. To be spacific, the thrid one from the top. I assume all four are the same?

 

[Pintglass]

These four. To be spacific, the thrid one from the top. I assume all four are the same?

There 0.1uf

 

[Chai_tea]

There 0.1uf

while searching, I've found something like "Chip Cap 0.1uF/10Vdc, ±10%" by AVA "parts number 060603ZC104KAT2A". Where 10Vdc is said to be the related voltage and there are many options like 2,4,6,10,50 and up to 100.

I doubt that the original one is 4 or 6. Or this does not matter at all as I assumed that the line is going to ground.

 

[The Real Jdbye]

while searching, I've found something like "Chip Cap 0.1uF/10Vdc, ±10%" by AVA "parts number 060603ZC104KAT2A". Where 10Vdc is said to be the related voltage and there are many options like 2,4,6,10,50 and up to 100.

I doubt that the original one is 4 or 6. Or this does not matter at all as I assumed that the line is going to ground.

I think 10V should be fine as they go to a chip and that most likely runs off of 3.3 or 5V but don't take my word for it. As long as the voltage limit of the cap is higher than the actual voltage you'll be fine.

 

[mrios]

Good morning to all,
The pasive components near to P13USB has been moved when I have tryed to replace the IC. Could you say me which is the component in blue in the attached photo ? In the site I don't see nothing about this component, only I,ve seen that it is a inductor, but I don'y sure. Could you help me, please ?. Thanks.

 

[Pintglass]

Good morning to all,
The pasive components near to P13USB has been moved when I have tryed to replace the IC. Could you say me which is the component in blue in the attached photo ? In the site I don't see nothing about this component, only I,ve seen that it is a inductor, but I don'y sure. Could you help me, please ?. Thanks.

It’s a 10 uf capacitor

 

[mrios]

Thank you so much.

 

[johneyreb03]

By chance would anyone know the two black components perpendicular to the ones in the red box?

 

[Modificatorul]

100 kohm size 0201

And use this thread if you need more info.

https://gbatemp.net/threads/compone...he-motherboard-and-main-console.525026/page-8


@johneyreb03

 

[Infante]

while searching, I've found something like "Chip Cap 0.1uF/10Vdc, ±10%" by AVA "parts number 060603ZC104KAT2A". Where 10Vdc is said to be the related voltage and there are many options like 2,4,6,10,50 and up to 100.

I doubt that the original one is 4 or 6. Or this does not matter at all as I assumed that the line is going to ground.

Hi,
I ask for your help and at the end where you bought the piece, thank you

 

[Infante]

I think 10V should be fine as they go to a chip and that most likely runs off of 3.3 or 5V but don't take my word for it. As long as the voltage limit of the cap is higher than the actual voltage you'll be fine.

Hello, I have the same problem as him, which could I buy.
Might you help me?
thanks