C:\Dokumente und Einstellungen\BoZz\Desktop\Chiip\AVRDude>avrdude -p m8 -c sp12
-U flash:w:chiip-v1_0_beta5-atmega8.hex -U lfuse:w:0xE3:m -v
avrdude: Version 5.2, compiled on Oct 21 2006 at 01:41:41
    Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
    System wide configuration file is "C:\Dokumente und Einstellungen\BoZz\
Desktop\Chiip\AVRDude\avrdude.conf"
    Using Port      Â: lpt1
    Using Programmer   Â: sp12
    AVR Part       Â: ATMEGA8
    Chip Erase delay   Â: 10000 us
    PAGEL         : PD7
    BS2          : PC2
    RESET disposition   : dedicated
    RETRY pulse      : SCK
    serial program mode  : yes
    parallel program mode : yes
    Timeout        : 200do
    StabDelay       : 100
    CmdexeDelay      : 25
    SyncLoops       : 32
    ByteDelay       : 0
    PollIndex       : 3
    PollValue       : 0x53
    Memory Detail     :
                ÂBlock Poll        Page
  ÂPolled
     Memory Type Mode Delay Size ÂIndx Paged ÂSize  Size #Pages MinW ÂMax
W Â ReadBack
     ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ---
-- ---------
     eeprom     4  Â10  128  Â0 no    Â512  Â0   Â0 Â9000 Â90
00 0xff 0xff
     flash     33   6  Â64  Â0 yes   Â8192  64  Â128 Â4500 Â45
00 0xff 0x00
     lfuse     Â0   0   0  Â0 no     Â1  Â0   Â0 Â2000 Â20
00 0x00 0x00
     hfuse     Â0   0   0  Â0 no     Â1  Â0   Â0 Â2000 Â20
00 0x00 0x00
     lock      0   0   0  Â0 no     Â1  Â0   Â0 Â2000 Â20
00 0x00 0x00
     calibration  Â0   0   0  Â0 no     Â4  Â0   Â0   0
0 0x00 0x00
     signature   Â0   0   0  Â0 no     Â3  Â0   Â0   0
0 0x00 0x00
    Programmer Type : PPI
    Description   : Steve Bolt's Programmer
     VCC   = 4,5,6,7,8
     BUFF  Â= Â(not used)
     RESET  = 3
     SCK   = 2
     MOSI  Â= 9
     MISO  Â= 11
     ERR LED = 0
     RDY LED = 0
     PGM LED = 0
     VFY LED = 0
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e9307
avrdude: safemode: lfuse reads as E1
avrdude: safemode: hfuse reads as D9
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
    To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "chiip-v1_0_beta5-atmega8.hex"
avrdude: input file chiip-v1_0_beta5-atmega8.hex auto detected as Intel Hex
avrdude: writing flash (1546 bytes):
Writing | ################################################## | 100% 0.67s
avrdude: 1546 bytes of flash written
avrdude: verifying flash memory against chiip-v1_0_beta5-atmega8.hex:
avrdude: load data flash data from input file chiip-v1_0_beta5-atmega8.hex:
avrdude: input file chiip-v1_0_beta5-atmega8.hex auto detected as Intel Hex
avrdude: input file chiip-v1_0_beta5-atmega8.hex contains 1546 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.56s
avrdude: verifying ...
avrdude: 1546 bytes of flash verified
avrdude: reading input file "0xE3"
avrdude: writing lfuse (1 bytes):
Writing | ################################################## | 100% 0.00s
avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xE3:
avrdude: load data lfuse data from input file 0xE3:
avrdude: input file 0xE3 contains 1 bytes
avrdude: reading on-chip lfuse data:
Reading | ################################################## | 100% 0.00s
avrdude: verifying ...
avrdude: 1 bytes of lfuse verified
avrdude: safemode: lfuse reads as E3
avrdude: safemode: hfuse reads as D9
avrdude: safemode: Fuses OK
avrdude done. ÂThank you.