I’m currently saving up to buy some sort of old PlayStation. Should I buy a PS3 or PS2? And also, which model of those consoles will cost me the least in the long term?
PS2 emulation is pretty good, I don't really see the need to own a PS2 these days. I have one with FMCB but find it more convenient to play them in emulator, where I have higher resolutions and wireless controllers.I’m currently saving up to buy some sort of old PlayStation. Should I buy a PS3 or PS2? And also, which model of those consoles will cost me the least in the long term?
Didn’t they remove native support for PS2 games on the slim and super slim? Or did they just remove physical support?PS3 will last longer and you can mod it to play PS1 & PS2 isos (along with other things).
Didn’t they remove native support for PS2 games on the slim and super slim? Or did they just remove physical support?
They did.Didn’t they remove native support for PS2 games on the slim and super slim? Or did they just remove physical support?
Didn’t they remove native support for PS2 games on the slim and super slim? Or did they just remove physical support?
Ah k thxAs has been stated, only native support via hardware was removed. Can still play PS2 isos via the PS3's built in software emulation.
Just for the record, Retro Fighters has made a wireless controller for PS1, PS2, PS3, and PC. Supports all features across all generations, including pressure sensitive front buttons, gyro, and similar. Highly recommended checking out if you're interested in either real hardware or emulation and want something without a wire. It's called the Defender and I'm quite happy with mine.PS2 emulation is pretty good, I don't really see the need to own a PS2 these days. I have one with FMCB but find it more convenient to play them in emulator, where I have higher resolutions and wireless controllers.
Sony never made a wireless controller for the PS2 AFAIK and the third party ones I got were MadCatz, so, yeah...
Which games do you want to play? The PS3 can play some PS1 and PS2 games, but a lot of them are not compatible. The backwards compatibility with especially PS2 games is only good on the first generation PS3's and those definitely don't last longer then PS2's.
In my opinion PS2's have less problems then PS3's. The only frequent thing that dies in PS2's are the lasers. But there are different other ways to play PS2 games on them and if it's needed, replacing the laser isn't very difficult or expensive.
First of all, at this point you could probably afford both. If you can't or don't want to get both, I'd say go for a PS3. For the PS2 you can use PCSX2, an amazing emulator that by now has near perfect support for all games and can run on almost any modern PC. It doesn't even require a real GPU and will run perfectly fine with integrated graphics. Alternatively you can emulate it even on a cheap Raspberry Pi using AetherSX2, though it's no longer being developed, but you can get the last build from the Wayback Machine.
Emulating the PS2 at this point is better than original hardware, since it had no HD support at all, had only analog outputs (and most new TVs don't even have analog inputs anymore, though you can use RCA to HDMI converters), no wireless controllers (there are some 3rd party Chinese controllers but they're total crap from my experience). Also running backups from USB disks is plain awful - the PS2 only has USB 1,1, and games will be slower than from the original DVD disc. Things will run a lot better if you use an internal HDD, but mind that's only possible with fat PS2s and the PS2 is pretty picky about which drives it accepts.
In other words, using an emulator, even on a 10 year old PC with integrated graphics, will run games faster and with better graphics than original hardware.
The PS3 on the other hand is still worth buying. It's a huge leap forward - it has full HD 1080p support via native HDMI (no 4K UHD though, sorry), and can double as a Blu-Ray player as well. As for emulators, there is a good PS3 emulator called RPCS3. Good, but not perfect. There are still a few games that don't run at all and many games whose FPS is unacceptable. Also, RPCS3's system requirements are pretty high. While you can run PCSX2 on an office PC just fine, RPCS3 actually requires a gaming PC. This means that for playing PS3 games, the original hardware is still the better - and cheaper option.
Early PS3s were also backwards compatible with PS2 games, but this has been removed pretty early in the PS3 lifecycle and I wouldn't recommend getting one of those, because they're notoriously unreliable. Get a slim or super-slim (depending on whether you want to mod it) PS3 instead, and use an emulator for PS2 games. All PS3 models (and PS2s) are backwards compatible with PS1 games though, although the PS2 has better PS1 compatibility due to it actually having PS1 hardware in it. Still, if you use a PC for PS2 games you will probably want to use it for PS1 games as well. At this point, the PS1 can be perfectly emulated on a toaster.
As for which specific PS3 model:
* If you don't want to mod it, or if HEN is sufficient for you, get a super-slim CECH-43xx. It's the only model guaranteed to have the 28nm GPU, considered to be the most reliable. The super-slims may look ugly but they're actually the most reliable. Make sure you have the NOR model and not the EMMC model. They can be easily told apart because the EMMC model has 16GB of built-in storage and will boot even without an internal HDD. The NOR model requires an HDD and always comes with one preinstalled. Even though the EMMC supports HDD as well, the firmware on these models is always on the EMMC, which is not a good thing because if certain things go wrong, EMMC models would get completely bricked while NOR models will only need to have the HDD reformatted.
* If you want to mod your PS3 with full CFW, get the slim CECH-25xx, which is considered to be the most reliable of the models that support CFW. They have the 40nm GPU, but these are only slightly less reliable than the 28nm, and shouldn't be too much of a concern. All slim models are NOR based so no need for EMMC concerns. The only issue is that only some 25xxs are compatible with CFW and there's no way of knowing just by looking at them from the outside. You'll need to run (or have the seller run) the MinVerChk tool to see the minimum supported firmware version. If it's 3.56 or below then it's CFW compatible, if it's 3.60 or above then it's not. If you can't find a seller willing to run that tool before you buy, get a CECH-21xx instead, which is the last model guaranteed to be
What’s the difference with HEN and full CFW?First of all, at this point you could probably afford both. If you can't or don't want to get both, I'd say go for a PS3. For the PS2 you can use PCSX2, an amazing emulator that by now has near perfect support for all games and can run on almost any modern PC. It doesn't even require a real GPU and will run perfectly fine with integrated graphics. Alternatively you can emulate it even on a cheap Raspberry Pi using AetherSX2, though it's no longer being developed, but you can get the last build from the Wayback Machine.
Emulating the PS2 at this point is better than original hardware, since it had no HD support at all, had only analog outputs (and most new TVs don't even have analog inputs anymore, though you can use RCA to HDMI converters), no wireless controllers (there are some 3rd party Chinese controllers but they're total crap from my experience). Also running backups from USB disks is plain awful - the PS2 only has USB 1,1, and games will be slower than from the original DVD disc. Things will run a lot better if you use an internal HDD, but mind that's only possible with fat PS2s and the PS2 is pretty picky about which drives it accepts.
In other words, using an emulator, even on a 10 year old PC with integrated graphics, will run games faster and with better graphics than original hardware.
The PS3 on the other hand is still worth buying. It's a huge leap forward - it has full HD 1080p support via native HDMI (no 4K UHD though, sorry), and can double as a Blu-Ray player as well. As for emulators, there is a good PS3 emulator called RPCS3. Good, but not perfect. There are still a few games that don't run at all and many games whose FPS is unacceptable. Also, RPCS3's system requirements are pretty high. While you can run PCSX2 on an office PC just fine, RPCS3 actually requires a gaming PC. This means that for playing PS3 games, the original hardware is still the better - and cheaper option.
Early PS3s were also backwards compatible with PS2 games, but this has been removed pretty early in the PS3 lifecycle and I wouldn't recommend getting one of those, because they're notoriously unreliable. Get a slim or super-slim (depending on whether you want to mod it) PS3 instead, and use an emulator for PS2 games. All PS3 models (and PS2s) are backwards compatible with PS1 games though, although the PS2 has better PS1 compatibility due to it actually having PS1 hardware in it. Still, if you use a PC for PS2 games you will probably want to use it for PS1 games as well. At this point, the PS1 can be perfectly emulated on a toaster.
As for which specific PS3 model:
* If you don't want to mod it, or if HEN is sufficient for you, get a super-slim CECH-43xx. It's the only model guaranteed to have the 28nm GPU, considered to be the most reliable. The super-slims may look ugly but they're actually the most reliable. Make sure you have the NOR model and not the EMMC model. They can be easily told apart because the EMMC model has 16GB of built-in storage and will boot even without an internal HDD. The NOR model requires an HDD and always comes with one preinstalled. Even though the EMMC supports HDD as well, the firmware on these models is always on the EMMC, which is not a good thing because if certain things go wrong, EMMC models would get completely bricked while NOR models will only need to have the HDD reformatted.
* If you want to mod your PS3 with full CFW, get the slim CECH-25xx, which is considered to be the most reliable of the models that support CFW. They have the 40nm GPU, but these are only slightly less reliable than the 28nm, and shouldn't be too much of a concern. All slim models are NOR based so no need for EMMC concerns. The only issue is that only some 25xxs are compatible with CFW and there's no way of knowing just by looking at them from the outside. You'll need to run (or have the seller run) the MinVerChk tool to see the minimum supported firmware version. If it's 3.56 or below then it's CFW compatible, if it's 3.60 or above then it's not. If you can't find a seller willing to run that tool before you buy, get a CECH-21xx instead, which is the last model guaranteed to be CFW compatible.
HEN does like 80% of what CFW does. It will allow you to play homebrew and backups just fine.What’s the difference with HEN and full CFW?