hi , how your modded oled ? i 'm facing a problem boot to hekate everytime i off my oled. everytime i on my oled it automatic boot to ofw directly and need restart few time to enter hekate. how bout yours?New OLED specific chip from AliExpress installed successfully. Not recommended for quick and easy installs. The flex PCB for the CPU bends too much, puts a bit of pressure on the CPU resistors in my opinion, but it's strong enough to hold, I'm not worried. The flex PCB up top is just garbage...takes ALOT of time to get it right, I even cut off part of it and manually wired 3.3v and ground.
TLDR: This new OLED model is poorly designed, but works. Be prepared to put in extra time to install it properly.
Hopefully this helps you out if you get this revision
u already solved your problem? try take out your sdcard and force shutdown your consoleask
help
switch oled hwfly
after apply tema and reboot not boot
blink cyan after that red solid and gone
no boot hekate menu
i try 10 time not work/not boot
Hi, so I was installing an oled v3 chip (locked chip) and then this happened, the cpu shield touched the clk point. Now I can't boot ofw at all, black screen. Any suggestions? Thanks!I haven't done it, but what happens if you ground out the D (CLK?) Point from scraping away too much at it?
Sthetix posted a new video explaining and showing the solution to this issue. Mainly, this issue is caused by the DAT0 adapter only connecting to the DAT0 point via friction. Reflowing the EMMC and anchoring the DAT0 adapter solves the issue. I also experience this on my OLED and the way I make sure it boots again is to force it to shut down and wait for 24hrs before turning it on again.ask
help
switch oled hwfly
after apply tema and reboot not boot
blink cyan after that red solid and gone
no boot hekate menu
i try 10 time not work/not boot
Sthetix posted a new video explaining and showing the solution to this issue. Mainly, this issue is caused by the DAT0 adapter only connecting to the DAT0 point via friction. Reflowing the EMMC and anchoring the DAT0 adapter solves the issue. I also experience this on my OLED and the way I make sure it boots again is to force it to shut down and wait for 24hrs before turning it on again.
Hello to everyone! I have some issues after instaling oled chip... when i plug in battery, and doesn't even push power button, chip led start light with white-blue colour. Flashing firmware seems ok during process... voltage drop also OK, anyone have thoughts about this?
Hello to everyone! I have some issues after instaling oled chip... when i plug in battery, and doesn't even push power button, chip led start light with white-blue colour. Flashing firmware seems ok during process... voltage drop also OK, anyone have thoughts about this?
try flash the modchip firmware to 0.62. try check your sp1 and sp2 cable in diode mode. black to the ground and red to green point and blue point.Hello to everyone! I have some issues after instaling oled chip... when i plug in battery, and doesn't even push power button, chip led start light with white-blue colour. Flashing firmware seems ok during process... voltage drop also OK, anyone have thoughts about this?
Thnks!!!! I'l will try in closest time!try flash the modchip firmware to 0.62. try check your sp1 and sp2 cable in diode mode. black to the ground and red to green point and blue point.
Hello to everyone! I have some issues after instaling oled chip... when i plug in battery, and doesn't even push power button, chip led start light with white-blue colour. Flashing firmware seems ok during process... voltage drop also OK, anyone have thoughts about this?
Was he able to resurrect the same switch that you had trouble with the install on? I am having the same exact BAD0010D error and when I remove the chip my switch won't do anything.De9ed did my Oled for me. Very fast, great communication, and reasonable prices. If you see some of my earlier posts, you will notice I tried to do an HWFLY lite in Oled (before the new Oled specific version) and botched it pretty bad. De9ed helped me out and I have a wonderful Oled with Oled chip running beautifully.
accidental double postDe9ed did my Oled for me. Very fast, great communication, and reasonable prices. If you see some of my earlier posts, you will notice I tried to do an HWFLY lite in Oled (before the new Oled specific version) and botched it pretty bad. De9ed helped me out and I have a wonderful Oled with Oled chip running beautifully.
actually, I think this is what I did to the first OLED that I bricked. I broke the via. Is this something you have the skills to repair by running a wire from that trace, to the emmc? I Assume it would involve removing and re-balling the emmc (something I really don't think I can handle myself).The 'point' is a bit of trace going to a via, which ends up underneath the eMMC itself. If this trace is damaged, or the via is damaged, or if either is bridged to the surround ground plane, then there will be no communication possible between cpu and emmc, so bootrom can't execute the bct. Either the screen will remain off or show purple.
The trace is there. If you recall, I had a heck of a time with the solder mask (and really crappy uv light) on top of bad joints, and I ended up going too deep and breaking the via. If I go back and clean that pad really good, you can actually see a hole in the center of it. reaaaallly tiny hole...It can't be done without removing and re-flowing the emmc, can it? It would be neat, if I could revive it myself...If the trace for clk is still there then it's quite easy. If not, the tegra must also be lifted and reballed to restore the trace.