Hardware Components used on the Switch (mostly the motherboard and main console)

[MasterCPU]

Hi! I'm hoping someone might be able to help. So I've search through the forum and the internet and I'm trying to track down the connector on the Switch motherboard that the Game Card Slot/HeadPhone PCB ribbon connects down into. I've attached a picture with the connector in question circled in blue. To give you some background, I have a Nintendo Switch where parts of the touchscreen do not respond to touch. I've replaced the Digitizer, so I don't believe it's that. I've also swapped out the Game Card Slow/Headphone PCB. If you look closely at the picture of the connector, you can see on the left side that the metal end cap of the connector is missing. I thought I could try jumping a wire across, but I believe that connection makes a connection on the Game Card/Headphone Jack PCB ribbon which in turn connects through to the Digitizer. So if anyone has any ideas on where I can get that connector or other possible ideas on fixing the issue without replacing the connector, I'd appreciate it. Thank you!

 

[SolidSnakeUk89]

hey, I get them from here

https://www.aliexpress.com/item/400...1.0&pvid=2900487b-405a-4358-9e0d-c7d1779b48b8

 

[andersabra]

Would anybody be able to ID this in the red square for me please?

 

[RocknRola]

Hey Guys,
i need ur help.
Can u tell me what that part is ?
Its burned , and the 2 marked capacitors are shorted (Still without IC)

 

[Adrill]

Hello, is it confirmed that all the resistors around the BQ24193 are 10K ohms?
I managed to blew some off with the hot air gun when I changed the BQ
When I checked their values on another Switch, some were 10K, but not all of them.

 

[Pintglass]

Hello, is it confirmed that all the resistors around the BQ24193 are 10K ohms?
I managed to blew some off with the hot air gun when I changed the BQ
When I checked their values on another Switch, some were 10K, but not all of them.

No there's different sizes, post an image of where you've blown them of

 

[Adrill]

No there's different sizes, post an image of where you've blown them of

It's those three:

 

[RocknRola]

Hey Guys,
i need ur help.
Can u tell me what that part is ?
Its burned , and the 2 marked capacitors are shorted (Still without IC)

Answered it myself,
Its a 20Ball BGA with the Label EN56.
reversed the lines on PCB and found out it has something to do with the Audio Codec Chip.

 

[Crossfader]

Hi, is this the same Panasonic Filter as on the back by the PI13USB?

 

[psi_lizard]

Hi everyone! Could any of you please help me with the values for this cap that is missing next to the MicroSD card reader connection?

Update: I ended up buying another broken switch to harvest the cap off of after I didn't get any hits on the forums that I posted. I tested it and it seems to be 4.7µF if anyone in the future stumbles across this post.

 

[PuntoMovil]

Anyone know the value of this component? Thanks in advance

 

[FXDX]

Anyone know the value of this component? Thanks in advance

As far as i know is a fuse, size it’s 0402, 2.5-3.5A 32V
I think you can try this:

https://eu.mouser.com/ProductDetail/Bourns/SF-0402FP350F-2?qs=sGAEpiMZZMtxU2g/1juGqWJziY9CkRY0q3bf57mmt23FjtSoMtlV0Q==

 

[Atomical]

Does anyone know the value or what type of component this is? Presume Capacitor.

History of the switch, Daughter dropped it in to the dogs water bowl last night while turned on. Saw the screen fade as I was wiping away the water. Stripped down today and cleaned the board with isopropanol in areas that looked corroded (only a few small spots, but board was dry all over), but noticed this chip circled was scorched,

The switch is modded with Atmosphere and has to be RCM with a payload to boot, can detect in windows and seen in TegraRcmGUI. With no payload and with payload injected. So hopefully just that component stopping it from booting.

Thanks in advance

 

[Atomical]

Here's a pic of the actual board area.

Meter confirms short on this.

 

[Pintglass]

Here's a pic of the actual board area.

Meter confirms short on this.

Are you talking aboult the large component, if so this should be shorted as its an inductor.

 

[Atomical]

I wasn't sure what it was but thanks for confirming.

Found an issue with the backlight ribbon (Think its that) one of the traces is gone. Must have been when i washed with IPA.

I guess there is no fix for this apart from a new screen? or is somthing like wire glue good enough?

 

[Pintglass]

I wasn't sure what it was but thanks for confirming.

Found an issue with the backlight ribbon (Think its that) one of the traces is gone. Must have been when i washed with IPA.

I guess there is no fix for this apart from a new screen? or is somthing like wire glue good enough?

I did manage to fix a ribbon cable like yours by using a piece of copper foil soldered across the break but it wasn't as bad as yours, you've only got a small bit of the trace left at the end. If you've got some copper foil it would't do any harm to try it.

 

[Liorsh]

Hello
I appreciate if someone can assist me
this switch first edition

have been connected to AliExpress cheep rock that made it stop working.

It doesn’t turn on the battery is full and all the electronics rotes to the common problems of can’t find shortage with my fluke near theme.
The only shortage I found is what I marked in the pictures in yello market left side all the electronics there have shortage.
I couldn’t find information on line regarding this problem.

anyone have any ideas?

 

[mixelpixx]

Here's a pic of the actual board area.

Meter confirms short on this.

Looks like that ceramic cap and the diode possibly should be replaced..

 

[Pintglass]

Hello
I appreciate if someone can assist me
this switch first edition

have been connected to AliExpress cheep rock that made it stop working.

It doesn’t turn on the battery is full and all the electronics rotes to the common problems of can’t find shortage with my fluke near theme.
The only shortage I found is what I marked in the pictures in yello market left side all the electronics there have shortage.
I couldn’t find information on line regarding this problem.

anyone have any ideas?

When you say there shorted which components do you mean theirs a lot in the image you've posted highlighted in yellow